Error Code P2735: What It Means & What To Do?
OBD Code P2735 - Pressure Control Solenoid "F" Intermittent
This
is an OBD error code related to the pressure control solenoid of your vehicle.
The P2735 error is defined as a Pressure Control Solenoid "F"
Intermittent. Your vehicle has a Transmission Control Module which helps in
shifting the gears smoothly so that you have a smooth and safe drive. The TCM
will employ the Pressure Control Solenoids to be able to control the hydraulic
pressure which is required to be able to apply the different clutch packs in
the transmission. This helps in matching different gear ratios to propel the
vehicle smoothly on road. If the TCM is able to detect an error with the
Pressure Control Solenoid it will set the P2735 code.
Learn More About OBD Error Code P2735
The
Pressure Control (PC) Solenoid Valve is basically an electronic pressure
regulator which performs the task of controlling the transmission line
pressure. It is done based on the current flow through the coil windings, when
the current flow increases the magnetic field which is produced by the coil
moves the plunger of the solenoid away from the exhaust port. When the exhaust
port opens it decreases the output fluid pressure which is regulated by the PCM
solenoid valve, this in turn will decrease the line pressure. The line pressure
solenoid valve helps in regulating the oil pump discharge pressure as per the
need of the driver. This is done in response to the signal sent from the TCM.
What causes this problem with the Pressure Control Solenoid
"F" Intermittent?
- The transmission fluid level is below the needed
level
- There’s dirt in the transmission
fluid
- Fault in the line pressure solenoid valve 'F'
- The harness of the Line
pressure solenoid valve 'F' is either open or shorted
- Poor electrical connection is present at the Line pressure solenoid valve 'F' circuit
Replace/Repair These Parts To Fix OBD Code P2735
- Pressure Control
Solenoid - The PC solenoid is responsible for controlling the fluid pressure to the internal friction plate
clutches/ drum bands. When the PC solenoid doesn’t work properly it can cause
slipping, which can result in the transmission overheating. Don’t be stuck with
a faulty Pressure Control Solenoid, fix it or buy a replacement on PartsAvatar
and get rid of the P2735 code today!
- Electronic Pressure
Regulator - Maintain outlet pressure
at the desired level, they do so with the help of a push valve and vent valve.
There’s a small pressure sensor which monitors the output pressure and the set-point is maintained by the servo
valves with the help of a digital or analog
controller. A faulty regulator can cause trouble to your vehicle, fix the issue
via repairs or opt for easy replacements from PartsAvatar. We offer free
shipping on orders over $99.
- Transmission Control
Module - Is the module that controls the transmission of
your vehicle. The TCM has to b in super working conditions so that your vehicle
can change gears easily and move smoothly on the road. If you have found the
problems with the TCM, try to repair them first and see if the P2735 code
persists. If it does, then you will. have to go for replacement. Find the TCM
fitment for your vehicle online on PartsAvatar. We ship to the remotest corners
of Canada from our warehouses.
- Powertrain Control
Module - The brain of your vehicle which manages the
functions of all the other solenoids and modules. The PCM has to work in top
condition to avoid codes like P2735 to set. Try to repair the PCM first, as
replacement may be pricey but also need reprogramming by a professional
diagnostician. If you need a replacement look no further, we have a wide range
of PCMs available for you on our website. Select from a vast range of prices to
fit your budget.
- Transmission Filter - This can become clogged with debris or even get damaged. You will need
to replace it as it could have been the reason why the P2735 code was set in
the first place. Find transmission filters on our website, and order from the
comfort of your home and have them delivered to you in just a matter of days.
- Transmission Pump - A
faulty transmission pump may have caused the P2735 code
to set. Find a resolution by fixing the damages to the pump, there may also be
leakages or clogs in the pump. If that doesn’t help you will have to replace
it.
- Transmission Valve Body - This is known as the control center of the transmission. It has a maze
of channels as well as passages which sends hydraulic fluid to the different
valves. This in turn helps in gear changes. A problematic valve body can cause
multiple issues, and harm the TCM. Try to repair and see if the P2735 code is
corrected, if not you will have to go for replacement. PartsAvatar offers a
wide range of the replacement transmission valve bodies. You can avail free
shipping on orders over $99.
Symptoms Of OBD Error Code P2735
It is vital to know the symptoms of
an issue as only then you would be able to solve the problem. So that’s why we
have listed out some major symptoms of OBD Code P2735 here:
Common Symptoms
- Vehicle is put into limp mode for
safety
- The Transmission slips
when trying to shift
- Overheating of the Transmission
- The Transmission
catches in gear
- Lowered fuel economy
- Misfire-like symptoms are
present
- The Check Engine Light is on
How To Correct P2735 Pressure Control Solenoid "F" Intermittent
Have a look at some ways with which
you can correct the P2735 code:
- Change the
contaminated the fluid and damaged filter
- Repair or replace the
faulty Pressure Control Solenoid
- Repair or replace the faulty transmission pump
- Repair or replace the defect in the transmission valve body
- Flush the in order to
clean the passages
- Clean the corrosion present on the
connectors
- Try to repair the damaged wiring or replace it
if needed
- Flash or replace faulty PCM
To do all this, you will need a few high-quality auto parts such as pressure control solenoid valve, electronic pressure regulator, transmission control module, transmission filter, transmission pump, transmission valve body and so on. From where will you get them? From your local store? Well, why go there when you can order quality parts with us while sitting in the comfort of your home. So, just browse through our website and order your needed parts today.
Easy Diagnosis Of Engine Error OBD Code P2735
Here are some steps which you should
follow in order to diagnose this P2735 fault code:
The first step is to research the Technical
Service Bulletins (TSB’s). For this you will have to match your vehicle’s year
of manufacture, model and transmission. The reason why the TSB should be
referred is mainly to save you time, and effort. It serves as a great tool
during diagnosis.
Fluid check -Measure the level of fluid and also
observe the condition of the fluid for any dirt or contamination. Don’t be
hasty in changing the fluid, check the vehicle records to see when the fluid
and filter change was done last. Depending on what you have found, you can
proceed to changing the fluid or simply skip this step if the fluid level and
purity is good.
Wiring inspection- Moving on to the wiring,
perform a detailed visual examination and see if there are any damages present.
Continue inspection of the connectors and see if the pins are corroded, bent or
damaged. Check the wires and connectors going to the transmission pressure
solenoids, transmission pump as well as the PCM. Depending on the type of
vehicle the transmission pump may be driven electrically or mechanically. Fix
all the issues you have found by conducting repairs or replacements as
required.
Continuity Check- These will be done to figure
out the problem if it wasn’t with the fuel, filter or electrical components.
Continuity check is an advanced step, and hence will need certain tools
like a digital multimeter and the
specific technical references for the vehicle. Get hold of them and also all
the troubleshooting information for your particular vehicle from the TSBs.
Voltage Check- To confirm the voltage and fluid
pressure requirements you will need to refer the TSBs. In terms of continuity
checks, they will usually be 0 ohms of resistance, but for safety refer your
vehicles information source. When performing the continuity checks you have to
ensure that power is removed from the circuit. This is important to avoid
shorting the circuit and causing more damage to the vehicle. If you find that
there is no continuity or resistance then that’s an indication that there is
faulty wiring present which may be open or shorted and needs to be
repaired/replaced.
Common Mistakes When Diagnosing the P2735 Code
- A problem with the Engine
misfire
- Issue with the Transmission
pump
- Presence of an Internal
transmission problem
- Driveline Issue