P0440 - OBD Trouble Code

<<See All OBD Codes

The P0440 trouble code would start appearing when the computer would detect that the EVAP system is not functioning properly. It would start indicating that there is a part of the EVAP control system which is not working as it should. There are a number of parts in the EVAP system like the gas cap, carbon canister, fuel lines, purge valve as well as some other hoses. The EVAP discharge control system would prevent the escape of the fuel vapours from the fuel system of the car. The fuel vapours are then routed through the hoses to the charcoal container for storage. Now when the car engine would start running, then the purge control valve would be opened and thus it would allow the intake vacuum to draw the fuel vapours to the car engine.

The trouble code P0440 can be defined as Evaporative Emission Control System Malfunction.

Generally, the most typical fault code which is related with the EVAP is the P0440 trouble code, which might indicate a leak which is usually a loose-fitting gas cap. This code would indicate that there is something within the EVAP system which is not functioning properly.

What causes this problem with the Evaporative Emission Control System Malfunction?

• The gas cap might not be installed properly
• Failure in the purge solenoid
• The canister might not be plugged and not working properly
• There can be a loose or damaged gas cap
• The EVAP hose might be leaking or disconnected
• Defaults in the purge valve
• Quirks in the canister vent valve
• There can be a leakage in the charcoal canister
• The fuel tank might be leaking

1. Fuel Tank - Did your mechanic just found out that there is some fault in the Fuel Tank? Buy top notch Fuel Tank from us at economical prices.
2. Carbon Canister - A damaged Carbon Canister can cause a lot of issues. It would be nice if you get it replaced on time.
3. Gas Tank Sealer - Everything is fine with the Carbon Canister and still OBD code P0440 flashing? Then there is definitely some fault with the Gas Tank Sealer. Get it checked and replace if needed.
4. Charcoal Canister - Charcoal Canister is an important car part which should never be neglected. May be there is some fault in it due to which P0440 code may start flashing.
5. Purge Solenoid - A faulty Purge Solenoid can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Evap Purge Valve - If everything is alright with Charcoal Canister, then there is surely some defect in Evap Purge Valve. Get it replaced before the situation gets worse.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that?s why we will help you to diagnose P0440 code by mentioning some major symptoms below:

Common Symptoms

• The check engine light can start illuminating and the code might be set in ECM memory
• There can be a fuel vapour odour in or around the vehicle

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0440:

• You must inspect the EVAP system for cuts/holes in tubes/hoses
• Carefully check for damaged or disconnected hoses around the EVAP purge solenoid
• Replace the sensor if found faulty
• Inspect the purge valve
• The fuel cap should be tightened or resettled
• You can always replace leaking fuel cap that has a bad seal or vent in the cap
• Repair or replace the leaking vapour system components like a vapour control valve or carbon canister

However, if you face any issue then we have stocked a wide range of best Fuel Cap, Cap Auto, Gas Cap, Fuel Transfer Tank, Evap Canister and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• The first step is to scan the codes and document the code in the ECM
• The freeze frame data should be viewed to check when the fault actually occurred
• Inspect the entire fuel system including the fuel lines and vapour lines from the front to the rear of the vehicle for any signs of fuel or vapours leaking
• Carefully check to be sure that the fuel cap is not lose as this is the most common problem
• A smoke leakage test should be performed on the fuel vapour system to try and locate the cause of the vapour leak using the test vapour port
• If no leaks are present, then follow the manufacturer pinpoint test for detailed checking of the vapour sensor and system for this code since these systems can be very different between manufacturers

Common Mistakes When Diagnosing The P0440 Code

• A common mistake can be assuming the gas cap is leaking without actually doing a proper diagnosis of all the parts
• There can be one more mistake which can be done by a mechanic is to fail to check with its customers if the gas cap was left loose recently