Guide To P0443 OBD Error Code Solutions

<<See All OBD Codes

The evaporative emissions system would allow the fumes from the gas tank to enter the car engine to be burned rather than vented into the atmosphere in the form of an emission. The purge valve solenoid is supplied with switched battery voltage.

The P0443 error code can be described as Evaporative Emission Control System Purge Control Valve Circuit Malfunction. This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another. This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

What causes this problem with the Evaporative Emission Control System Purge Control Valve Circuit Malfunction?

• Driver circuit which is inside powertrain control module can be faulty
• Wiring harness chafing or rubbing another component causing short or open on control circuit
• There can be an internal short or open in the purge solenoid
• The connector might be worn, broken or shorted due to water intrusion

1. Gas Tank Sealer - There can be some issues with the Gas Tank Sealer due to which you may see P0443 code appearing over and over again. Visit us to buy best quality Gas Tank Sealer online.
2. Fuel Tank - A lot of issues can arise do to defective Fuel Tank. Did you just see P0443 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Carbon Canister - Faulty Carbon Canister can be the reason why P0443 code is flashing. Visit us to purchase top notch Carbon Canister online.
4. Purge Solenoid - It is an important auto part which needs full care. A faulty Purge Solenoid can be a reason behind the flashing up of P0443 code.
5. Evap Purge Valve - Are you facing some faults in your Evap Purge Valve? Don’t worry and get them replaced or else P0443 code can turn up.
6. Charcoal Canister - Common cause behind this P0443 error code can be some fault in Charcoal Canister. So, it will be a good decision to replace them now.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Noticeable fuel odour can be caused by escaping water vapour
• Appearing of the check engine light
• There can be a slight drop in fuel mileage
• ” Whooshing” sound caused by excessive pressure in the gas tank when removing the cap, which might indicate malfunctioning or stuck closed purge valve
• Rough running engine might be caused by stuck open purge valve 

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• The defective leak detection pump should be replaced
• The damaged EVAP lines or canister should be repaired
• Make sure to repair open or short in voltage feed circuit to purge solenoid
• Open in PCM purge command circuit should be repaired properly
• Replace the faulty purge solenoid
• The vacuum switch should be repaired or replaced if needed
• Restore restriction in EVAP line or canister or solenoid
• You can always repair resistance in purge connector
• If there are some faults in the PCM, then it should be surely replaced

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Fuel Cap, Cap Auto, Gas Cap, Fuel Transfer Tank, Evap Canister and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• The first and the foremost step is to scan the codes and document the code in the ECM, and then view the freeze frame data see when the fault happened
• Carefully check the entire vapour purge valve wiring and system to include the purge valve connector for corrosion, damaged or loose connection or wires
• Checks the purge valve vent for any blockage from dirt, debris, or spider webs
• Perform a smoke leakage test on the fuel vapour system to try and locate the cause of the vapour leak by using the test vapour port
• The purge control valve should then be checked for proper resistance of valve and then check operation of valve using the ECM to control the valve

Common Mistakes When Diagnosing The P0443 Code

• Most of the times people simply assume that the purge control valve is faulty without actually doing proper diagnosis, but in reality, the issue might be with the wiring
• One another big mistake can be not verifying the failure and replacing parts that may or may not be the problem