Guide To P010A OBD Error Code Solutions

<<See All OBD Codes

Is your car?s Malfunction Indicator Lamp Illuminating? Are you experiencing rough engine idles and the engine is stalling and not starting occasionally? Is there loss of engine power and black smoke emitting from the tailpipe? All these might indicate towards problem of MAF sensor/circuit, thus leading the OBD code P010A being stored in the PCM (Powertrain Control Module).

OBD-II Code Decreased engine performance is defined as a Mass or Volume Air Flow "B" Circuit.

The MAF (mass air flow) sensor is mounted in the vehicle's engine air intake tract downstream from the air filter that measures the volume and density of air being drawn into the engine. The powertrain control module (PCM) uses that reading to ensure proper fuel delivery at any given time for optimum power and fuel efficiency. OBD Code P010A means that there is a detected problem with the Mass Air Flow (MAF) sensor or circuit. The PCM detects that the actual MAF sensor frequency signal is not performing within the normal expected range of the calculated MAF value, and thus flashed this error. PCM can also make the vehicle go into failsafe mode to avoid any damage to the engine and also illuminate Malfunction Indicator Light (MIL).

What causes the problem in Mass or Volume Air Flow B Circuit?

• Faulty MAF (Mass Air Flow) sensor
• Leakage in Intake Air System
• Dirty MAF sensor and air filter
• Open or shorted Mass air flow sensor harness
• Poor electrical connection to the Mass Air Flow sensor circuit

1. Mass Air Flow Sensor - Replace faulty MAF sensor to avoid wrong reading of the intake air sending to the PCM, thus affecting the fuel delivery system. Buy new sensors from us now!
2. Air Intake Kits - It is important to recognise problem in the air intake system as it affects the air to fuel ratio as thus the combustion process. Thus, replace faulty air intake kits now!
3. Air Filters - Contaminated air will affect the air and fuel mixture composition and can damage the engine as well. Clean the clogged filters and replace if damaged.
4. Diagnostic Tool - Choose from our wide variety of diagnostic tools to detect and correct the OBD code error.

It is important to note the symptoms indicating the OBD Code P010A to check for specific errors and problems.

Common Symptoms

• Malfunction indicator lamp (MIL) illumination
• Rough engine idles and accelerations
• Black smoke emission from tailpipe
• Engine stalling and not starting
• Engine hard start or stalling after it starts
• Other drivability symptoms or sometimes even no symptom at all

There can be some components that when damaged and replaced can immediately resolve this problem. Some of these immediate go to components that can be faulty and need replacements are mentioned below:

• Replacement of Intake Manifold Gasket
• Replacement of Mass Airflow Sensor

At Parts Avatar Canada find quality replacement parts to solve any OBD error problem. We have genuine parts for all vehicle make and model and the best prices for all your auto parts needs. Shop now!

• First step is to inspect all MAF (Mass Air Flow) sensor wiring and connectors to make sure they are intact, not frayed, broken, routed too close to ignition wires/coils, relays, motors, etc.
• Check for any obvious leakages in the air intake system
• Closely inspect the MAF sensor wires or film to see if you can see contamination such as dirt, dust, oil, etc.
• Replace the air filter, if dirty, with a new original equipment filter from the dealer.
• Clean the MAF carefully, using MAF cleaner spray.
• Check, if the air intake system has a mesh in it, and clean as necessary.
• Check for the faulty MAP for vacuum leakages and replace if necessary.
• This OBD code can set at idle or during deceleration, if there is a low minimum air rate through the sensor bore. Inspect for any vacuum leaks downstream of the MAF sensor.
• Use an OBD-II scan tool to monitor real-time sensor values from the MAF sensor, O2 sensors, etc.
• Always check for Technical Service Bulletins (TSBs) for your particular make/model in case of known issues on your vehicle.
• Make sure that the barometric pressure (BARO) that is used in order to calculate the predicted MAF value is initially based on the MAP sensor at key ON.
• The MAP sensor can cause this error, if there is high resistance on the ground circuit. Thus, it is important to replace faulty MAP immediately.

Common mistakes when diagnosing the P010A code

• Not checking for Intake manifold leaks
• Not examining Mass Air Flow (MAF) sensor failure
• Powertrain Control Module (PCM) failure undetected
• Not checking the wiring and connectors in relation to the sensor and connector properly