Error Code P0C5A: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0C5A can be explained as Drive Motor "A" Position Sensor Circuit "B". The resistance of the thermistor which is built into the motor temperature sensor would change as per the changes in the temperature of the MG2. Now if the temperature of the MG2 would be low, then the higher would be the resistance of the thermistor. In the similar way, the rise in temperature would mean fall in the overall resistance. This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

Do you want to know more about the P0C5A fault code? Don’t worry! Parts Avatar Canada is here at your service. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. Now when the PCM or any of the other control modules would indicate faults in the Drive Motor "A" Position Sensor Circuit "B", then it would give rise to the P0C5A trouble code.

What causes this problem with the Drive Motor "A" Position Sensor Circuit "B"?

• Imperfect hybrid vehicle motor
• Unbolted hybrid vehicle motor harness
• Unacceptable electrical connection in the hybrid vehicle motor circuit
• Quirks in the HV control ECU

1. Generator Assembly - If there are some faults in your car generator assembly, then it would lead to illumination of the service engine light, dim lights as well as some odd noises might start coming. Buy top notch car generator assembly from us at economical prices.
2. HVAC Blower Motor Control Module - It is an electrical component, which is a part of automobile’s heating and air conditioning system. It makes sure to control the blower motor fan speed. If there are some defects in it, then it would be nice if you get it replaced on time.
3. Motor Assembly - The motor assembly is a very important component of your vehicle. When it stops working, so does your car. Get it checked and replace if needed.
4. Engine Control Module - If there is any corrosion or breaks in the internal wiring of the harness, then it can cause a short in the ECM or can also cause corrosion in the ECM through the wiring harness. You can always rely on us as we have best auto parts for our customers.
5. Powertrain Control Module - The onboard computer, or powertrain control module is the brain of the engine control system. Now if the brain is not working properly, then neither is the car engine. Get it replaced before the situation gets worse.
6. Electronic Control Unit - Is your car jump starting on reverse polarity? Or are you facing some intermittent starting issues? If yes, then it indicates that your electronic control unit is bad. So it is very important to replace the defective electronic control unit with us at equitable prices.

There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P0C5A? Your wish is our demand. Have a look at them below:

Common Symptoms

• There can be an illuminated engine light

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Make sure to mend the faulty hybrid vehicle motor assembly
• Rehabilitate the defaults in the engine control module
• The malfunctioning hybrid vehicle motor assembly harness should be repaired or replaced as per the need
• Carefully adjust the faults in the motor control module
• The hybrid battery should be restored to working order
• Adjust the flawed car exhaust system parts

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of drive motor generator, motor position sensor, motor control module, generator assembly, drive motor output shaft and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0C5A code to be stored:

• The mechanic or the technician will use a diagnostic scanner or code reader like DVOM to visually scan for the error codes in the vehicle.
• After performing a careful inspection, every of the stored codes and freeze frame data are retrieved as it can help down the way for further diagnosis process.
• Most often he has to inspect the solenoid itself to see if they are faulty or damaged. Additional error codes that are stored in the vehicle are also addressed.
• The mechanic performs a continuity test between the PCM and solenoid to check the resistance.
• If the drive motor "A" position sensor circuit and other related parts are not faulty, he will then re-tune the code and test drive the vehicle.
• On test driving, if the P0C5A code does not return soon, he will know that an erratic condition exits.
• But if the error returns instantaneously, he will check every components of the drive motor "A" position sensor circuit as well motor assembly, generator assembly etc for any possible fault.
• If any component is damaged, he will fix them right away.
• After performing this repair, he will inspect the drive motor "A" position sensor circuit as well.
• Every time a repair work is carried out, make sure that the mechanic test drives the vehicle after every repair so that the diagnosis is successful. This can eventually help him to know as to where the error occurred.

Common Mistakes When Diagnosing The P0C5A Code

• Non observance of the drive motor generator assembly