P0C5B OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0C5B can be defined as Drive Motor "A" Position Sensor Circuit "B" Range/Performance. If the powertrain control module would detect an issue with the drive motor "A" position sensor circuit "B" range/performance, then it would give rise to the P0C5B error code. The particular code which is triggered depends upon the specific fault which the PCM has detected.

It is always good to learn more! That is the reason why we are here to help you out in gaining more knowledge about the P0C5B error code. The thermistor resistance which is built into the motor temperature sensor would change as per the changes in the temperature of the MG2. Now if the temperature of the MG2 would be low, then the higher would be the resistance of the thermistor. Similarly, the increase in temperature would mean decrease in the resistance.

What causes this problem with the Drive Motor "A" Position Sensor Circuit "B" Range/Performance?

• The hybrid vehicle motor might be flawed
• Hybrid vehicle motor harness is not shut or tiny
• Hybrid vehicle motor circuit poor electrical connection
• Malfunctioning HV control ECU

1. Generator Assembly - Some common symptoms of bad generator assembly are weak or dead car battery, weird smells and the warning light on the dashboard might start illuminating. It would be nice if you get it replaced on time.
2. HVAC Blower Motor Control Module - If there is a failure in the blower motor resistors’ internal components, then it might cause the HVAC blower motor control module to malfunction, or it might not function at all on one or more of the settings. Get it replaced before the situation gets worse.
3. Motor Assembly - One of the most common causes of the failure in the motor assembly can be due to neglecting oil changes. Remember that oil is the lifeblood for engines. You can always rely on us as we have best auto parts for our customers.
4. Engine Control Module - There can be some engine performance issues due to faulty engine control module. If the ECM fails or has any problems it can lead to performance issues with the vehicle like misfires, hesitation, loss of power, and sometimes even decreased fuel economy.
5. Powertrain Control Module - PCM stands for powertrain control module. It is a car part, a control unit which is utilized on motor vehicles. It is generally a combined control unit, consisting of the engine control unit (ECU) and the transmission control unit (TCU).
6. Electronic Control Unit - If your automobile's check engine light remains on constantly, and never goes off, there's a good chance that your vehicle has a damaged electronic control unit. There are a lot of reasons why a car's check engine light will remain on. The most common reason is a defective ECU.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0C5B code by mentioning some major symptoms below:

Common Symptoms

• Visibility in the check engine light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0C5B:

• Make sure to mend the faulty car exhaust system parts
• It is essential to restore the flawed hybrid vehicle motor assembly harness
• Rehabilitate the defaults in the motor control module
• Carefully adjust the faults in the engine control module
• The auxiliary battery relay should be restored to working order
• Recondition the non-functioning hybrid vehicle motor assembly

However, if you face any issue then we have stocked a wide range of best priced drive motor generator, motor position sensor, motor control module, generator assembly, drive motor output shaft and more to help you out in fixing your car..

Here are some steps which you should follow in order to diagnose this fault code:

• This is a general type of error code which is diagnosed with the help of a scanner.
• The mechanic will insert a scanner to diagnostic port of the vehicle and recover the codes and freeze frame data.
• If he happens to find any additional error codes, he has to address them as well.
• Once it is done, he has to reset the vehicle, and then test drive to see if the error code appears.
• If the error code does not return, then there can be an erratic condition.
• Then the mechanic has to check the wires, connectors and other electrical components and quickly replace them if he finds them to be damaged or defective.
• Check for the damaged drive motor "A" position sensor circuit and its components for error. It the mechanic finds the fault in the connectors in relation to the battery, replace it immediately.
• Also check for the particular parts which are related to the drive motor "A" position sensor circuit like generator assembly and motor assembly.
• Parts or components should not be replaced with reference to only a P0C5B DTC. The vehicle service manual should be consulted for more information on possible causes of the fault, along with required testing.
• If all the components seems to work perfectly, inspect the PCM for faults and replacement along with reprogramming.

Common Mistakes When Diagnosing The P0C5B Code

• There can be some faults in the drive motor generator assembly