Error Code P0929: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0929 can be elucidated as Gear Shift Lock Solenoid/Actuator Control Circuit "A" Range/Performance. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. This trouble code is associated to the transmission, and includes pressure defaults as well as failures in the sensors. If an error in the gear shift lock solenoid circuit would be detected by the transmission control module, then it would give rise to the P0929 trouble code.

Are you tensed because the P0929 fault code is flashing? We have everything which you need and at equitable prices. You must visit us and we promise that you will never regret your decision. One thing which you must keep in mind that its symptoms as well as causes would surely vary as it depends upon a number of things. A gear shift lock solenoid is utilized by the automobile with an automatic transmission to ensure that your car cannot be shifted out of “Park” without the brake pedal being depressed. Now when the car engine has been turned ON and the brake pedal is completely depressed, then the gear shift lock solenoid would allow the automobile to shift from “Park” to “Reverse” or “Drive.” Now when the engine control module would detect some issues in the voltage reading or signal from the gear shift lock solenoid, then the P0929 trouble code would start flashing up.

What causes this problem with the Gear Shift Lock Solenoid/Actuator Control Circuit "A" Range/Performance?

• There can be less transmission fluid
• The transmission fluid might be grubby
• Less battery voltage
• The electrical wiring to or from the gear shift lock solenoid might not be functioning properly
• There can be distorted gear shift lock solenoid
• Quirks in the brake light switch
• Some issues related to the ECM

1. Automatic Transmission Fluid - There can be some issues with the Automatic Transmission Fluid due to which you may see P0929 code appearing over and over again. Visit us to buy best quality Automatic Transmission Fluid online.
2. Engine Control Module - A lot of issues can arise do to defective Engine Control Module. Did you just see P0929 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Car Battery - Faulty Car Battery can be the reason why P0929 code is flashing. Visit us to purchase top notch Car Battery online.
4. Automatic Transmission Sensor - It is an important auto part which needs full care. A faulty Automatic Transmission Sensor can be a reason behind the flashing up of P0929 code.
5. Auto Transmission Shift Solenoid - OBD Code P0929 can appear because of faulty Auto Transmission Shift Solenoid.
6. Powertrain Control Module - There can be some issues with the Powertrain Control Module due to which you may see P0929 code appearing over and over again. Visit us to buy best quality PCM online.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Appearance of the service engine soon light
• Automobile might not shift out of park

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• It is essential to change the transmission fluid
• You must fix the defective car battery
• Make sure to fill the transmission fluid to manufacturer recommended levels
• Repair or replace the quirky brake light switch
• The malfunctioning engine control module should be repaired or replaced as per the need
• Recondition the non-functioning gear shift interlock solenoid

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of engine light, electrical wiring, brake pedal, brake light switch, manual transmission fluid and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• It would be a great idea to use an OBD-II scanner to inspect for a stored P0929 trouble code.
• The transmission fluid level should be inspected properly.
• Examine the transmission fluid quality.
• Now if you find out that the transmission fluid is grubby, then inspect the transmission pan for signs of clutch debris or other contaminants.
• Scan the battery voltage/charge
• Visually look at the wiring and electrical system for any obvious signs or defects.
• Examine for any blown fuses.
• The gear shift lock solenoid for continuity should be tested properly.
• You can always check the brake light switch for continuity.

Common Mistakes When Diagnosing The P0929 Code

• Failure in the transmission control module
• Non performance of the gear shift actuator assembly
• Wiring might start failing