P092A OBD Error Code: Problem & Solutions

<<See All OBD Codes

This diagnostic fault code is a generic Powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

OBD Code P092A - Gear Shift Lock Solenoid/Actuator Control Circuit "B"

It is important to understand that the gear shift lock solenoid works as a mechanism that manages the gear shift and keeps the vehicle in park position until the brake pedal is pressed. Thus when the shift lock solenoid is not functioning properly, and the control circuit is damaged, it will not be able to interpret the gear shifts. Thus when the gear shift lock solenoid control circuit is faulty, it will not send the correct signals to the PCM and thus OBD code P092A will get stored in the system.

What causes this problem with the Gear Shift Lock Solenoid/Actuator Control Circuit "B"?

• Faulty Gear Shift Lock Solenoid
• Open/short harness to the Gear Shift Lock Solenoid
• Poor electrical connections to Gear Shift Lock Solenoid circuit
• Gear shift actuator assembly failure
• Transmission Control Module (TCM) failure
• Powertrain Control Module failure

1. Shift Lock Connector - If the connector is faulty, the circuit sensor will not be able to interpret the shift condition and thus will hamper the performance. Buy new shift lock connectors now!
2. Shift Interlock Actuator - Check for faulty actuator and replace it now. Buy new shift lock actuator form us!
3. Shifter Lock Relay - Faulty relay will affect the shifter lock functionality and thus needs to be replaced immediately. Buy new shifter relay today!
4. Automatic Transmission Control Module - TCM faults can also lead to transmission failures and thus must be replaced immediately. Buy new TCM now!
5. Ignition System Parts - This error code can also be due to affected ignition timing and thus might need certain components to be replaced. Buy new ignition system parts from us!
6. Exhaust System Parts - There can also be instances of increased emissions from the exhaust and might need examination for repairs and replacements. Thus, check and replace faulty components today!
7. Cylinder Head Gaskets - Leakages through cylinder heads must be taken seriously and thus will need immediate replacement. Buy new cylinder head gaskets now!
8. Diagnostic Tool - Choose from our wide variety of diagnostic tools to detect and correct the OBD code error.
9. Engine Control Module - OBD Error Code P092A can also be due to faulty ECMs. This may lead to engine stalling or not starting, and check engine lights being on. It’s better to get the faulty electricals replaced as soon as possible.
10. Powertrain Control Module - P092A error code also relates to problems with the Powertrain Control Module. Find all the Powertrain related parts with us.

Willing to know some common symptoms of OBD Code P092A? Your wish is our demand. Have a look at them below:

Common Symptoms

• Check Engine Light On
• Gear not engaging from park to drive
• Vehicle not starting
• Increased fuel consumption
• Improper transmission shifts
• Smoke coming from under the hood
• Other driveability symptoms or sometimes even no symptom at all

We have listed out some ways which would help you to correct the occurrence of OBD Code P092A. They are mentioned here as follows:

• Gear Shift Lock Solenoid Replacement
• Gear Shift Lock Solenoid Harness Replacement
• Gear Shift Actuator Assembly Replacement
• Transmission Control Module (TCM) Replacement

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Transmission, Gear Shift Lock Solenoid, TCM, Torque, Transmission Fluid, Control Module, Cylinder Head Gasket, Exhaust System, MAF Sensor, Fuel Trim, Oxygen Sensor and many more. Now all your problems would vanish within no time.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

• Make use of a digital volt ohm meter (DVOM) for the complete test. Continue through the tests until the problem is confirmed. You will also need a basic OBD code scanner to reset the computer and erase the code.
• Always check for a dead battery first, as it can be a common problem for car not starting and replace it immediately.
• First check the level and quality of the transmission fluid. If the fluid is low, add more and retest the system.
• If the transmission fluid appears dirty or contaminated, and/or it smells burnt, the mechanic will flush the system, change the transmission fluid, clear the code, and retest once more.
• Inspect and test the transmission for internal mechanical problems, circuit problems, and issues with the shift solenoid. After each repair, they will clear all codes and retest the vehicle to see if the P092A code appears again.
• Check for leakages through head gaskets and repair or replace as required.
• Al do inspect for increased emission through exhaust system that might require assistance in terms on any mechanical failure.
• It is important understand that the gear shift lock solenoid, connector and wiring can wear out over time. Thus, replace faulty components immediately.
• Never rule out the possibility if TCM/PCM failure that might require replacement and reprogramming.

Common Mistakes When Diagnosing the P092A Code

The most common mistake while diagnosing P092A code is misdiagnosis of an engine misfiring issue or a problem with the vehicle’s drive line. If the system is not thoroughly inspected and diagnosed, it can also look like an internal transmission problem when it’s actually a much simpler and less expensive issue.