P0928 - OBD Trouble Code

<<See All OBD Codes

The trouble code P0928 can be explained as Gear Shift Lock Solenoid/Actuator Control Circuit 'A'/Open. This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another. The transmission control module keeps an eye on the gear shift lock solenoid. The P0928 error code would be set by the transmission control module when the gear shift lock solenoid would not be as per the parameters set by the manufacturer to the vehicle.

We believe that an investment in knowledge pays the best interest. So why not learn more about the P0928 error code? This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

What causes this problem with the Gear Shift Lock Solenoid/Actuator Control Circuit 'A'/Open?

• There can be inoperative gear shift lock solenoid
• Gear shift lock solenoid harness might be opened or shorted
• Imperfect electrical connection in the gear shift lock solenoid circuit

1. Muffler - A faulty Muffler can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Powertrain Control Module - If everything is alright with Exhaust System Parts, then there is surely some defect in Powertrain Control Module. Get it replaced before the situation gets worse.
3. Exhaust System Parts - P0928 code can display due to some issues in the Exhaust System Parts. So it is very important to replace the Exhaust System Parts with us at equitable prices.
4. Auto Transmission Control Module - Do you remember when was the last time you got your Auto Transmission Control Module checked up? A dirty Auto Transmission Control Module can cause a lot of issues like displaying P0928 code.
5. Catalytic Converter - Poor Catalytic Converter can cause a lot of difficulties, so why not get it replaced at time?
6. Engine Control Module - There can be some issues with the Engine Control Module due to which you may see P0928 code appearing over and over again. Visit us to buy best quality Engine Control Module online.

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0928 here:

Common Symptoms

• There can be increasing fuel consumption
• Transmission may not move in the correct manner

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• You must deactivate the cylinders
• Make sure to mend the faulty gear shift lock solenoid
• It is essential to restore the flawed gear shift lock solenoid harness
• Repair or replace the quirky powertrain control module
• Rehabilitate the defaults in the catalytic converter

Parts Avatar Canada endeavour’s to fulfil all the needs of its consumer, that’s why we have a huge collection of top quality custom exhaust, dual exhaust tips, exhaust catalyst, truck mufflers, car catalyst, true dual exhaust and many more at equitable prices. We won’t let you down in any way.

Here are some steps which you should follow in order to diagnose this fault code:

If there is some issue with the cylinders, then the crankshaft sensor would provide a signal to the fuel injection computer or the ignition control. Due to this a spark would be created by the ignition coil and the fuel would be injected by the injector into each and every cylinder at the correct time. Now if any sensor is not working accurately, then because of this the car would start running roughly and at the same time the car engine would turn out to be less effective. In the latest car modules, the car would normally keep the automobile running, but there would be an appearance of the engine warning light on the dashboard.

Common Mistakes When Diagnosing The P0928 Code

• There can be some faults in the gear shift actuator assembly
• Non observance of the transmission control module
• Negligence in the wiring