Guide To P07AC OBD Error Code Solutions

<<See All OBD Codes

There’s a hybrid control module in your vehicle, the job of which is to monitor the transmission clutch for correct operation. If in case the control module detects that the clutch isn’t activating as commanded, then it will set the error code P07AC. The vehicle may also be put on ‘limp mode’ by the hybrid control module, the purpose of this is to limit engine/transmission performance in order to prevent further damage to the transmission system.

The ECM will only activate the P07AC code and other related ones after proactively monitoring and adjusting other sensors and systems. It does this to ensure that correct self-diagnosis happen. Hence, it is important to address this issue before you continue using your vehicle, otherwise you will have much more damage to resolve. When this error is present, it could also be because of some complex internal electrical malfunctions too, so it is important to ensure that only a professional look at your vehicle and is able to derive correct diagnosis. Not knowing the correct issue can result in expensive corrections, so be careful. The letter ‘F’ in the error refers to few different possible distinctions, you could be having an issue with a particular circuit/wire or friction element within the transmission. To find out locations of all these components, refer your vehicles manual. This OBD error code P07AC is set by the ECM upon detecting a slip in the internal ‘F’ friction element present inside the transmission being stuck off, or not engaging or gripping. There could also be a performance problem of the transmission.

What causes this problem with the Transmission Friction Element “F” Performance Stuck OFF

• Low level of ATF
• Worn internal friction element
• Dirty ATF Causes
• Wiring problems like open, shorted or chafed, heat damage etc.
• Uneven sized tires
• Issues causing uneven rotational speed/circumference like low tire pressures, brake stuck on and so on
• Issue with TCM/Transmission Control Module
• Issue with ECM (Engine Controls Module)
• Issue with water damage to module and/or harness

1. Powertrain Control Module - If your PCM issue isn’t getting resolved by repairs you will have to go for replacement. At Parts Avatar we provide a wide range of branded Auto Parts that will suit your vehicle. Simply go online and order from the comfort of your home!
2. Engine Control Module - The ECM module is a very important component, try to repair it, if that is not helping you will have to opt for replacement. Be careful and go for only the best. You can speak with our online customer support agent for any queries you may have.
3. Automatic Transmission Module - After diagnosis of the error code P07AC, if you have concluded that a transmission change is required, don’t worry we have the best one for you. We offer amazing prices and also the best quality.
4. Transmission Control Module - Purchase a new one from Parts Avatar, and vail free shipping on orders over CAD $99

We have listed few common symptoms associated with Transmission Friction Element “F” Performance Stuck OFF

Common Symptoms

• Uneven handling
• Slipping of Transmission
• Haphazard shifting
• Atypical shift patterns
• Difficult shift selection
• Leak ATF (Automatic Transmission Fluid)
• Low torque
• Power output abnormal

Here are some ways by which you can correct OBD error code P07AC

• Check transmission fluid quality and accordingly change it
• Check level of transmission fluid and add more as needed
• Repair and replace the faulty transmission system
• Repair and replace Powertrain Control Module

Take a look at our superior variety of PCM, ECM, Body Control Module, Engine Control Module and many more auto parts. Now all your problems would vanish within no time.

Diagnosing your vehicle for an OBD code require patience and diligence. Make sure you have all the tools and information needed at your disposal so that you can follow diagnostic steps mentioned below with ease:

Research your vehicles TSB (Technical Service Bulletin) to compare the issues you are facing. This is the first and very important troubleshooting step for resolving OBD errors. If the problem is severe, the advance diagnostic steps will require advanced equipment and knowledge.

Step 1 - You will have to perform basic maintenance procedures, start with checking the fluid as it is a crucial part of your transmission systems health. The Automatic Transmission Fluid has to be clean, free from contaminant, and hence regular maintenance schedule should be followed. If you are unable recall the last maintenance check, it’s best to run one to be safe. Check the filter, fluid and gasket.

Step 2 - Locate the junction connector, this will be present in the system, you may find it when you look for connector/harness for the transmission system. Ensure you’re working with the correct one, refer your manual for it, there’s one “master” connector too. So double check that you’re working with the correct one. Start off by checking if the connector is seated properly and has good electrical connection. The point where the connector attaches the A/T it is subject to vibrations, these sometimes can make the connections loose or even physically damage them. Remember, the ATF can saturate the connectors and wires, which can cause issues in the present as well as future, so check for that too.

Step 3 - It is important to be weary of the overall condition of your vehicle. One system can very well affect the others adversely. Some issues like uneven tires, incorrect wheels, worn out suspension parts etc. can all cause issues in the A/T system and as well as others. In order to diagnose this code you will have to check them too, and correct the issues.

Common mistakes when diagnosing the P07AC code

• Internal transmission has failed
• Transmission fluid level has become low
• Transmission valve body solenoid has failed