Error Code P07A2: What It Means & What To Do?

<<See All OBD Codes

The trouble code P07A2 can be defined as Transmission Friction Element "A" Performance Stuck Off. The letter “A” in this case might refer to some possible differences. The person might be dealing with a particular circuit/wire or there can be a certain friction element within the transmission.

That is the reason why it is very important to have a look at your service manual for particular locations, distinctions, and other such specifications. When the engine control module would detect a slip in the internal "A" friction element inside the transmission, then P07A2 code would start appearing.

It is always good to learn more! That is the reason why we are here to help you out in gaining more knowledge about the P07A2 error code. There are lot of friction elements required when a mechanical operation of an automatic transmission is being considered. The same friction materials like the clutch as used by the manual transmissions.

Here we are referring to the automatic transmission. One thing which you must keep in mind that its symptoms as well as causes would surely vary as it depends upon a number of things. Just keep in mind that the initial thing which should be considered is the general health of the automatic transmission as well as automatic transmission fluid.

What causes this problem with the Transmission Friction Element "A" Performance/Stuck Off?

• Decrease in the ATF
• There can be shabby friction element
• Grimy ATF
• Open, short, chafe, heat damage in the wiring
• The tire sizes might be rough
• There can be problems which cause dissimilar rotational speed/circumference like low tire pressures, brake stuck on, etc
• Faults in the transmission control module
• Imperfect engine control module
• Module or harness might have water damage

1. Automatic Transmission Fluid - Did your mechanic just found out that there is some fault in the Automatic Transmission Fluid? Buy top notch Automatic Transmission Fluid from us at economical prices.
2. Engine Control Module - A broken Engine Control Module can cause a lot of issues. It would be nice if you get it replaced on time.
3. Auto Transmission Control Module - Everything is fine with the engine control module and still OBD code P07A2 flashing? Then there is definitely some fault with the Auto Transmission Control Module. Get it checked and replace if needed.
4. Electronic Control Unit - Electronic Control Unit is an important car part which should never be neglected. May be there is some fault in it due to which P07A2 code may start flashing.
5. Body Control Module Component - A faulty Body Control Module Component can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Powertrain Control Module - If everything is alright with Body Control Module Component, then there is surely some defect in Powertrain Control Module. Get it replaced before the situation gets worse.
7. Automatic Transmission Filter - P07A2 code can display due to some faults in the Automatic Transmission Filter. So, it is very important to replace the Automatic Transmission Filter with us at equitable prices.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P07A2 code by mentioning some major symptoms below:

Common Symptoms

• Irregular handling
• Automatic transmission fluid might start releasing
• Transmission sliding
• Unpredictable shifting
• Unusual shift patterns
• Grating shift selection
• Little torque
• Uncommon power output

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P07A2:

• You must fix the defective automatic transmission fluid
• Make sure to mend the faulty engine control module
• It is essential to restore the flawed automatic transmission control module
• Repair or replace the quirky electronic control unit
• Rehabilitate the defaults in the body control module component
• The malfunctioning powertrain control module should be repaired or replaced as per the need
• Carefully adjust the faults in the automatic transmission filter

However, if you face any issue then we have stocked a wide range of best priced Module, Friction Elements, Diagnostic Trouble, Transmission Oil, Pcm, Atf Fluid, Ecm Module and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

You must always start with a technical service bulletin search for your particular vehicle. Advanced diagnostic steps become very vehicle specific and may require the appropriate advanced equipment and knowledge to perform accurately. We include basic steps below but refer to a vehicle year/make/model/powertrain specific repair guide for specific steps for your vehicle.

It is very important to follow the basic maintenance procedures accordingly at this point, as far as the transmission's health goes, start at the fluid. Your ATF (Automatic Transmission fluid) should be fully clean, free of debris and also, proper maintenance schedules have to be followed to avoid more defects. If you don’t remember the last transmission has been serviced (i.e. filter+fluid+gasket), it’s a good idea to perform this before continuing. There might be a bit of debris in your oil that is trapped internally. It may only take a simple service, so make sure you are aware of the last A/T service

Now when you are attempting to search the connector/harness, then for that you will have to discover the junction connector. There may be one "master" connector so make sure you are working with the right one by referring to your manual. Make sure that the connector itself is seated properly to guard a fine electrical connection. Now when the connector is situated on the A/T, it may be subject to vibrations due to which the connections might become loose or physically damage them. Not to mention, the possibility of ATF to saturate connectors and wires causing future or present issues. All of us should be fully aware of the overall condition of your vehicle. Rough tires, worn out suspension parts, inaccurate wheels, all of these can and will cause issues in this system and possibly others as well, so even things out, and you may get rid of this code.

Common Mistakes When Diagnosing The P07A2 Code

• Nonperformance of the internal transmission
• Decrease in the transmission fluid level
• Failure in the transmission valve body solenoid