P076E OBD Error Code: Problem & Solutions

<<See All OBD Codes

P076E trouble code can be defined as Shift Solenoid H Intermittent. This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another.

This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

Do you want to gain some more knowledge about the P076E trouble code?

It is the shift solenoid valve ‘H’ which is turned ON or OFF by the transmission control module in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and engine control module. After that the gears would be shifted to the optimum position.

What causes this problem with the Shift Solenoid H Intermittent?

• The transmission filter might be stained
• Insufficient fluid level
• Flaws in the PCM
• Inoperative transmission valve body
• Contaminated fluid
• The shift solenoid might have some flaws
• There can be a crushed connector
• Some defects in the wiring
• Cramped hydraulic passages
• There can be an internal failure in the transmission

1. Powertrain Control Module - The P076E code can also arise due to some issues in Powertrain Control Module. So, it is advised to replace them as soon as possible.
2. Auto Transmission Valve Body Kit - Do you remember when was the last time you got your car Auto Transmission Valve Body Kit checked up? A damaged Auto Transmission Valve Body Kit can cause a lot of issues like displaying P076E code.
3. Automatic Transmission Master Rebuild Kit - Automatic Transmission Master Rebuild Kit is an important car part which should never be neglected. May be there is some fault in it due to which P076E code may start flashing.
4. Automatic Transmission Filter - Is your Automatic Transmission Filter damaged or broken? Don’t worry as we have solutions for all your problems.
5. Timing Gears - Defective car Timing Gears can be a major reason why P076E code depicts. So make sure to replace it online so that you don’t have to face any further issues.
6. Automatic Transmission Fluid - Everything is okay with the automatic transmission sensor and still OBD code P076E triggering? Then there must be some defects in Automatic Transmission Fluid. Replace them as soon as possible.
7. Automatic Transmission Sensor - Automatic Transmission Sensor is an important auto part. Take care of it and you can rely on us to purchase best quality Automatic Transmission Sensor online.

Willing to know some common symptoms of OBD Trouble Code P076E? Your wish is our demand. Have a look at them below:

Common Symptoms

• Transmission skidding
• Overheating of the transmission
• Flashing up of the check engine light
• Issue of transmission catches in gear
• Overall fuel economy can start declining
• There can be engine misfires
• Vehicle might start entering the limp mode

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P076E:

• Inspect the insufficient fluid level
• Correct the malfunctioning wiring
• Make sure that you repair the defective shift solenoid
• The faulty transmission valve body should be repaired or replaced
• Repair or replace the defective powertrain control module
• If you find out that the transmission filter is dirty or clogged, then it should be repaired or replaced
• Correct the internal failure in the transmission

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade TCM, Engine Light, Transmission Clutch, Quality Transmission, Precision Transmission, Manual Transmission Fluid, Transmission Oil, Auto Transmission, Solenoid Car, Atf Fluid and a lot more for our precious customers.

Check for technical service bulletins which pertain to the vehicle, symptoms, and codes prior to beginning the troubleshooting process for any malfunction. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. You can always check the vehicle records to verify the last time that the filter and fluid was changed if possible. Here are some steps:

• The first step is to make sure the fluid level is correct and inspect the condition of the fluid for contamination.
• After that perform visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots should be performed.
• Next is to check the connectors and connections for security, corrosion and damaged pins. This process must include all wiring and connectors to the transmission solenoids, transmission pump and the PCM.
• It depends upon the configuration; the transmission linkage should be inspected for security and binding issues.
• The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately.
• These procedures require a digital multimeter and the specific technical references for the vehicle.
• Voltage requirements will vary based of the specific year and model of the vehicle.
• You should follow the specific troubleshooting chart for your vehicle.
• Continuity checks should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data.
• Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.

Common Mistakes When Diagnosing The P076E Code

• Transmission control module might start failing
• Low transmission fluid level
• Some issues related to the wiring
• Faults in the transmission shift solenoid