P076C - OBD Trouble Code

<<See All OBD Codes

The fault codes which are related to this, the "H" solenoid, are codes P076A, P076B, P076D, and P076E. When this trouble code starts appearing, it would result in the illumination of the check engine light. If there is an overdrive or some other transmission warning lamp, then it might also start flashing up.

It is always good to learn more! That is the reason why we are here to tell you more about P076C fault code. A number of shift solenoids are included in a lot of automatic transmissions, and it all depends upon the number of gears which are inside.

The fault code P076C can be identified as Shift Solenoid H Stuck On.

What causes this problem with the Shift Solenoid H Stuck On?

• Polluted fluid
• The transmission filter might be dirty or clogged
• The fluid level might not be sufficient
• Flaws in the PCM
• Faults in the transmission valve body
• The shift solenoid might not be working properly
• Corroded or damaged connector
• Some defects in the wiring
• Cramped hydraulic passages
• There can be an internal failure in the transmission

1. Auto Transmission Valve Body Kit - There can be some issues with the Auto Transmission Valve Body Kit due to which you may see P076C code appearing over and over again. Visit us to buy best quality Auto Transmission Valve Body Kit online.
2. Automatic Transmission Master Rebuild Kit - A lot of issues can arise do to defective Automatic Transmission Master Rebuild Kit. Did you just see P076C code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Powertrain Control Module - Faulty Powertrain Control Module can be the reason why P076C code is flashing. Visit us to purchase top notch Powertrain Control Module online.
4. Automatic Transmission Sensor - It is an important auto part which needs full care. A faulty Automatic Transmission Sensor can be a reason behind the flashing up of P076C code.
5. Automatic Transmission Filter - OBD Code P076C can appear because of faulty Automatic Transmission Filter.
6. Timing Gears - There can be some issues with the Timing Gears due to which you may see P076C code appearing over and over again. Visit us to buy best quality Timing Gears online.
7. Automatic Transmission Fluid - Are you facing some faults in your Automatic Transmission Fluid? Don’t worry and get them replaced or else P076C code can turn up.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Transmission skidding
• Overheating of the transmission
• Issue of transmission catches in gear
• Overall fuel economy can start declining
• There can be engine misfires
• Vehicle might start entering the limp mode
• Flashing up of the check engine light

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Repair or replace the flawed shift solenoid
• Repair the flawed transmission filter
• Correct the malfunctioning transmission valve body
• Make sure that you repair the defective PCM
• Inspect the internal failure in the transmission
• You can always correct the insufficient fluid level
• The faulty wiring should be repaired or replaced

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of TCM, Engine Light, Transmission Clutch, Quality Transmission, Precision Transmission, Manual Transmission Fluid, Transmission Oil, Auto Transmission, Solenoid Car, Atf Fluid and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

Check for technical service bulletins which pertain to the vehicle, symptoms, and codes prior to beginning the troubleshooting process for any malfunction. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. You can always check the vehicle records to verify the last time that the filter and fluid was changed if possible.

Fluid & Wiring Inspections

• First thing which you should do is to check the fluid level and make sure it is correct and then check the overall condition of the fluid for contamination.
• Then visual inspection should be performed to check the associated wiring for obvious faults such as scraping, rubbing, bare wires, or burn spots should be performed.
• After that examine the connectors and connections for security, corrosion and damaged pins. All wiring and connectors to the transmission solenoids, transmission pump and the PCM should be included in this process.
• It is based upon the configuration; the transmission linkage should be checked for security and binding problems.

Advanced Steps

• The advanced steps become very vehicle specific and appropriate advanced equipment would be required to perform precisely.
• A digital multimeter and the specific technical references for the vehicle would be needed to carry out this procedure.
• Voltage requirements will differ depending upon the specific year and model of the vehicle.
• You should follow the specific troubleshooting chart for your vehicle.

Continuity Checks

• Perform the continuity checks with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data.
• Resistance or no continuity indicate that there are some faults in the wiring that is open or shorted.
• Get it repaired or replaced as per the need.

Common Mistakes When Diagnosing The P076C Code

• Some issues related to the wiring
• Low transmission fluid level
• Faults in the transmission shift solenoid
• Failure in the transmission control module