P076A OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P076A can be defined as Shift Solenoid H Malfunction.

The transmission control module turns ON or OFF the Shift solenoid valve 'H' in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and engine control module. Gears would then be shifted to the optimum position.

Do you want to gain more knowledge about the P076A trouble code? A number of shift solenoids are included in a lot of automatic transmissions, and it all depends upon the number of gears which are inside. When this trouble code starts appearing, it would result in the illumination of the check engine light. If there is an overdrive or some other transmission warning lamp, then it might also start flashing up.

What causes this problem with the Shift Solenoid H Malfunction?

• Smashed connector
• Quirky powertrain control module
• Dirty or clogged transmission filter
• Malfunctioning transmission valve body
• Confined hydraulic passages
• Defective wiring
• The fluid level might be inadequate
• Issue of dirty or contaminated fluid
• Internal damage in the transmission
• Unusable shift solenoid

1. Automatic Transmission Sensor - Did your mechanic just found out that there is some fault in the Automatic Transmission Sensor? Buy top notch Automatic Transmission Sensor from us at economical prices.
2. Timing Gears - Faults in the Timing Gears can cause a lot of issues. It would be nice if you get it replaced on time.
3. Powertrain Control Module - Everything is fine with the timing gear and still OBD code P076A flashing? Then there is definitely some fault with the Powertrain Control Module. Get it checked and replace if needed.
4. Automatic Transmission Fluid - Faults in the Automatic Transmission Fluid should never be neglected. May be there is some fault in it due to which P076A code may start flashing.
5. Automatic Transmission Filter - A faulty Automatic Transmission Filter can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Auto Transmission Valve Body Kit - If everything is alright with PCM, then there is surely some defect in Auto Transmission Valve Body Kit. Get it replaced before the situation gets worse.
7. Automatic Transmission Master Rebuild Kit - P076A code can display due to some issues in the Automatic Transmission Master Rebuild Kit. So, it is very important to replace the Automatic Transmission Master Rebuild Kit with us at equitable prices.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P076A code by mentioning some major symptoms below:

Common Symptoms

• Transmission sliding
• Transmission might start overheating
• Problem of transmission catches in gear
• Overall fuel economy can start declining
• There can be engine misfires
• Vehicle might start entering the limp mode
• Flashing up of the check engine light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P076A:

• If you find out that the transmission filter is dirty or clogged, then it should be repaired or replaced
• Correct the insufficient fluid level
• The faulty powertrain control module should be repaired or replaced
• Repair or replace the defective transmission valve body
• Correct the malfunctioning shift solenoid
• Make sure that you repair the defective wiring
• Inspect the internal failure in the transmission

However, if you face any issue then we have stocked a wide range of best priced TCM, Engine Light, Transmission Clutch, Quality Transmission, Precision Transmission, Manual Transmission Fluid, Transmission Oil, Auto Transmission, Solenoid Car, Aft Fluid and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

Research the technical service bulletins (TSBs) for the specific vehicle by year, model and transmission before you start with the troubleshooting process for any malfunction. There can be some situations where this can save a lot of your precious time in the long run by pointing you in the correct way. The vehicle records should be checked to verify the last time that the filter and fluid was changed if possible. First thing which you should do is to check the fluid level and make sure it is correct and then check the overall condition of the fluid for contamination. Then visual inspection should be performed to check the associated wiring for obvious faults such as scraping, rubbing, bare wires, or burn spots should be performed. After that examine the connectors and connections for security, corrosion and damaged pins. All wiring and connectors to the transmission solenoids, transmission pump and the PCM should be included in this process. It is based upon the configuration; the transmission linkage should be checked for security and binding problems.

The advanced steps become very vehicle specific and appropriate advanced equipment would be required to perform precisely. A digital multimeter and the specific technical references for the vehicle would be needed to carry out this procedure. Voltage requirements will differ depending upon the specific year and model of the vehicle. You should follow the specific troubleshooting chart for your vehicle. Perform the continuity checks with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity indicate that there are some faults in the wiring that is open or shorted. Get it repaired or replaced as per the need.

Common Mistakes When Diagnosing The P076A Code

• Defaults in the transmission shift solenoid
• Wiring related issues
• There can be a failure in the transmission control module
• Diminishing transmission fluid level