Guide To P044B OBD Error Code Solutions

<<See All OBD Codes

EGR sensor "C", EGR solenoid, EGR position sensor, and differential pressure feedback EGR sensor - Are these components causing problem in your engine? Then it more likely that you will notice an error OBD P044B. This is a common type of diagnostic trouble code which includes all models and makes. But, a few steps may vary depending on your engine make.

P044B is a trouble code which relates to the performance problem experiencing in the “C” electrical circuit to the exhaust gas recirculation (EGR) valve. The main aim of EGR valve is to push in a sufficient amount of exhaust gas into the intake manifold which in turn maintains the head temperature of the cylinder below 2500 degrees F. If the temperature increases more than 2500- degrees F then Nitrates of oxygen will be formed. The controlling computer – Powertrain control module or electronic control module has found an irregular low, high or non-existent signal voltage. Identify which “C” sensor is in your vehicle with the help of a manufacturer.

Just assume that the fuses and relays are in good condition. With the help of your vehicle’s information source you have to locate the PCM, TCM and power input signal circuit. Separate the connector from the PCM or TCM. Now place the ignition switch in on position and examine the exact circuit with the positive lead of the DVOM.

What causes this problem with the Random/Multiple Cylinder Misfire?

• Faulty EGR sensor “C”
• Damage in the wiring harness to the sensor
• Presence of carbon will prevent the EGR from opening or maybe it is stuck in the closed position
• Less vacuum to the EGR solenoid
• Fault in the EGR solenoid
• Fault in the position of the EGR solenoid
• A variance in the pressure feedback to the EGR sensor

1. EGR Solenoid - A faulty EGR solenoid has to be repaired or replaced with a new one.
2. EGR Position Sensor - If there are any leaks or damages in the position of the EGR sensor, wipe them clean or replace the damaged parts.
3. Pressure feedback EGR sensor - If the wiring harness of this component is shorted or damages, it will give rise to OBD error P044B. Replace them with the right components from Parts Avatar.
4. Wiring Harness - If you find any corrosion or leaks around the wiring joints wipe them clean and retest the vehicle again.
5. Electrical circuit - Damage / broken / faulty electrical circuit can disturb the entire engine system. Replace them immediately once the fault is found.

Interested in knowing the symptoms to OBD code P044B? If yes, then you have arrived at the right place. We at Parts Avatar have listed out few common symptoms associated with this fuel injector problem.

Common Symptoms

• If the service engine soon light is brightened, the P044B code will be set. Moreover, a secondary code relating to the failure of the EGR sensor may be set. High voltage relates to P044D code and low voltage signal signifies P044C error.
• If there is a partial opening in the EGR pintle, your vehicle will stand still and may not start.
• When there is a low load or high RPM you will hear a pin from the detonation or nil symptoms.

Have a look at some ways with which you can correct the P044B code:

• Replacing the EGR valve

Parts Avatar Canada is here to solve all your issues related to car parts. We have stocked a wide range of best priced Egr Solenoid, Egr Position Sensor, Pressure Feedback Egr Sensor, Wiring Harness, Electrical Circuit and a lot more to help you out in fixing your car.

In order to diagnose the Engine error Code P044B, you have to check if there is any fault in your engine. Some of them are mentioned below:

• There is one thing which is common with the EGR valves, they re-circulate from one exhaust to other to the intake manifold. Apart from this, they vary in their method of regulating the opening of a pintle or sensing its location. A few of the following procedures are the most common problems which results in majority of the EGR failures. You have to manually service the wiring joints and sensor failures with the right diagnostic procedure. Also, not that, wires differ from one manufacturer to the other. And the computer may not react if you examine the wrong wire. If you plan to send excessive voltage through the input terminal, the computer sensor will fry. Likewise, if you disconnect the wrong wire, the computer will lose its programming and a dealer has to reprogram it.
• This error mainly deals with the EGR sensor. So, check for corrosion, bents or loose connection. Clear the corrosion and reseat the connector.
• Remove both the electrical connector and EGR and check for coking in the intake of the exhaust. The pintle will move smoothly up and down if the coking is cleaned.
• Check the vacuum line from the EGR to the solenoid and substitute it if any faults are found.
• Check the solenoid electrical connector for erosion or faults.
• If you have a Ford car, follow the two vacuum pipes from the EGR to the differential pressure feedback EGR sensor in the tail of the manifold. Check the two pressure pipes for corrosion.
• Experience orders these plugs with carbon from the exhaust. Use a small pocket screwdriver or corresponding tool and clean the pipes of corrosion and the sensor will begin to function again.

Common Mistakes When Diagnosing the P044B Code

• Adequate exhaust leak.
• The engine fails to accelerate.
• Malfunction Indicator Lamp (MIL) is too bright.