P0540 - OBD Trouble Code

<<See All OBD Codes

P0540 error code can be defined as Intake Air Heater "A" Circuit.

The trouble code P0540 means that the powertrain control module has detected an abnormal input voltage from the intake air heater circuit.

The air is warmed with the help of intake air heater so that cylinder combustion happens correctly. Now during the cold operation, the ECM grounds the control coil of the intake air heater relay in order to energize the heater. If the engine control module would exceed the voltage reading from the manufacturer?s specifications during this process, then the P0540 trouble code would start appearing.

What causes this problem with the Intake Air Heater "A" Circuit?

• The connector might be damaged or corroded
• Damaged or restricted air duct
• Some faults in the wiring
• Faults in the heater element relay
• There can be some defects in the heater element
• Defective temperature sensor
• Flaws in the blower motor
• Powertrain control module might start malfunctioning

1. Engine Control Module - Did your mechanic just found out that there is some fault in the Engine Control Module? Buy top notch Engine Control Module from us at economical prices.
2. Air Intake temperature Sensor - A broken Air Intake temperature Sensor can cause a lot of issues. It would be nice if you get it replaced on time.
3. Electronic Control Unit - Everything is fine with the engine control module and still OBD code P0540 flashing? Then there is definitely some fault with the Electronic Control Unit. Get it checked and replace if needed.
4. Powertrain Control Module - Powertrain Control Module is an important car part which should never be neglected. May be there is some fault in it due to which P0540 code may start flashing.
5. Engine Wiring Connectors - A faulty Engine Wiring Connectors can be troublesome. You can always rely on us as we have best auto parts for our customers.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that?s why we will help you to diagnose P0540 code by mentioning some major symptoms below:

Common Symptoms

• Engine stalling issues
• Engine might not start at all
• Issue of longer than normal cranking time
• Check engine light might start illuminating
• There can be rough idle during cold temperatures

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0540:

• Make sure to clean corrosion from connectors
• Repair or replace the wiring
• The faulty air ducts should be replaced
• Replace the defective heater element
• If there are some faults in the temperature sensor, then it should be replaced
• Replacing the heater element relay
• Carefully restore the blower motor
• The malfunctioning powertrain control module should be replaced

However, if you face any issue then we have stocked a wide range of best priced engine light, blower motor, heating element, engine light on car, ecm car, honda engine light and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

The first and foremost step in troubleshooting process for any malfunction is to research the technical service bulletins for the specific vehicle by year, model and power plant. In some circumstances this can save a lot of time in the long run by pointing you in the correct direction

The intake air heating circuit might not work automatically if the ambient air or engine temperature is above the limit set by the manufacturer. The circuit should activate if it is commanded "ON" with a scanner, or if power is applied manually

Here are some basic steps:

• Carefully check the heater element, is it turning "ON"
• Inspect the blower motor, is it turning "ON"
• Visually inspect the circuit connections and wiring
• The condition of the air ducts for obvious defects should be visually inspected
• You must check the electrical connections for security and corrosion

Advanced Steps

Advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multimeter and the specific technical references for the vehicle. Voltage requirements will differ based of the specific year, model and the diesel engine in the vehicle

Specific Checks:

On applications that have Mass Airflow sensors, the intake air temperature sensor is incorporated into the sensor body. Consult technical data to determine the correct pins associated with the sensor

Perform specific checks using the troubleshooting guidelines for the specific vehicle using the technical manual or online reference material. These steps will guide you through the process of checking the power and ground to each component within the intake air heater circuit in the proper sequence. If the voltage is correct to a component that is not functioning, that component is most likely defective and requires replacement. If power is not available to operate the circuit, continuity checks may be needed to identify faulty wiring or components

Common Mistakes When Diagnosing The P0540 Code

• There are a lot of cases where the mechanics simply replace the air filters, or remove the air cleaner box for repairs during the process of tune up and would make a mistake of not reconnecting the intake air temperature sensor correctly
• Replacing the intake air heater relay or other parts can be a big mistake before carefully checking a bad connection