Error Code P0100: What It Means & What To Do?

<<See All OBD Codes

Is your car?s Malfunction Indicator Lamp Illuminating? Are you experiencing rough engine idles and the engine is stalling and not starting occasionally? Is there loss of engine power and black smoke emitting from the tailpipe? All these might indicate towards problem of MAF sensor/circuit, thus leading the OBD code P0100 being stored in the PCM (Powertrain Control Module).

OBD-II Code P0100 is defined as a Mass Air Flow Circuit Malfunction

The mass air flow (MAF) sensor is placed in the intake air duct between the air filter and the engine intake manifold. The MAF sensor measures the amount of intake air flow and converts the air flow measurement into a voltage or frequency signal, with the voltage or frequency changing proportionally to the amount of air flow.

The air flow sensor signal is monitored by the engine control module (ECM). The ECM uses the mass air flow signal to know the engine load and to calculate the proper amount of fuel injected. If the signal from the mass air flow sensor is out of expected range, the ECM detects a fault and sets the code P0100.

What causes the problem of Mass Air Flow Circuit Malfunction?

• Faulty MAF (Mass Air Flow) sensor
• Leakage in Intake Air System
• Dirty MAF sensor and air filter
• Open or shorted Mass air flow sensor harness
• Restricted airflow due to clogged air filters
• Poor electrical connection to the Mass Air Flow sensor circuit

1. Mass Air Flow Sensor - Replace faulty MAF sensor to avoid wrong reading of the intake air sending to the PCM, thus affecting the fuel delivery system. Buy new sensors from us now!
2. Air Filters - Contaminated air will affect the air and fuel mixture composition and can damage the engine as well. Clean the clogged filters and replace if damaged.
3. Diagnostic Tool - Choose from our wide variety of diagnostic tools to detect and correct the OBD code error.
4. Engine Control Module - OBD Error Code P0100 can also be due to faulty ECMs. This may lead to engine stalling or not starting, and check engine lights being on. It?s better to get the faulty electricals replaced as soon as possible.
5. Powertrain Control Module - P0100 error code also relates to problems with the powertrain control module. Find all the Powertrain related parts with us.

It is important to note the symptoms indicating the OBD Code P0100 to check for specific errors and problems.

Common Symptoms

• Malfunction indicator lamp (MIL) illumination
• Rough engine idles and accelerations
• Reduced fuel economy
• Engine stalling and not starting
• Engine hard start or stalling after it starts
• Other drivability symptoms or sometimes even no symptom at all

There can be some components that when damaged and replaced can immediately resolve this problem. Some of these immediate go to components that can be faulty and need replacements are mentioned below:

• Replacement of Intake Manifold Gasket
• Repair/Replace faulty wiring and connections
• Replace air filters
• Replacement of Mass Airflow Sensor

At Parts Avatar Canada find quality replacement parts to solve any OBD error problem. We have genuine parts for all vehicle make and model and the best prices for all your auto parts needs. Shop now!

First step is to inspect all MAF (Mass Air Flow) sensor wiring and connectors to make sure they are intact, not frayed, broken, routed too close to ignition wires/coils, relays, motors, etc.

• Check for any obvious leakages in the air intake system.
• Closely inspect the MAF sensor wires or film to see if you can see contamination such as dirt, dust, oil, etc.
• Replace the air filter, if dirty, with a new original equipment filter from the dealer.
• Clean the MAF carefully, using MAF cleaner spray.
• Check, if the air intake system has a mesh in it, and clean as necessary.
• Check for the faulty MAP for vacuum leakages and replace if necessary.
• This OBD code can set at idle or during deceleration, if there is a low minimum air rate through the sensor bore. Inspect for any vacuum leaks downstream of the MAF sensor.
• Use an OBD-II scan tool to monitor real-time sensor values from the MAF sensor, O2 sensors, etc.
• Always check for Technical Service Bulletins (TSBs) for your particular make/model in case of known issues on your vehicle.
• Make sure that the barometric pressure (BARO) that is used in order to calculate the predicted MAF value is initially based on the MAP sensor at key ON.
• The MAP sensor can cause this error, if there is high resistance on the ground circuit. Thus, it is important to replace faulty MAP immediately.

Common mistakes when diagnosing the P0100 code

• Not checking for Intake manifold leaks
• Not examining Mass Air Flow (MAF) sensor failure
• Powertrain Control Module (PCM) failure undetected
• Not checking the wiring and connectors in relation to the sensor and connector properly