Error Code P2701: What It Means & What To Do?

<<See All OBD Codes

The error code P2701 can be defined as Transmission Friction Element "B" Apply Time Range/Performance. There are a lot of modules as well as computers monitor and adjust a vast amount of components and systems in order to make the vehicle's operation seamless as well as effective. Automatic transmission is one out of those components as well as systems.

Want to learn something more about this fault code? Then you have arrived at the right place. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. If the transmission control module would detect a variation in the voltage coming from the control solenoid that is outside the parameters set by the automobile manufacturer, then it would store the P2701 error code. This would also give rise to the illumination of the check engine light.

What causes this problem with the Transmission Friction Element "B" Apply Time Range/Performance?

• Stoppage in transmission hydraulics
• Less ATF level
• Grubby ATF
• Transmission mechanical issues
• Wiring might be defective
• Flawed transmission valve body
• Quirks in the transmission control module
• There can be opened or shorted transmission control module harness
• Transmission control module (TCM) circuit poor electrical connection

1. Automatic Transmission Module - Faulty transmission module can cause problematic down shifts and upshifts, leading to stalling while accelerating or slowing down. This can also hamper many transmission system parts. Thus replace it now!
2. Engine Control Module - If there is any corrosion or breaks in the internal wiring of the harness, then it can cause a short in the ECM or can also cause corrosion in the ECM through the wiring harness. You can always rely on us as we have the best auto parts for our customers.
3. Transmission Fluid Pump Harness - The fluid pump harness can also be faulty causing transmission to underperform due to transmission slipping and harsh shift. Thus, check for harness faults and replace it now!
4. Powertrain Control Module - The onboard computer, or powertrain control module is the brain of the engine control system. Now if the brain is not working properly, then neither is the car engine. Get it replaced before the situation gets worse.
5. Transmission Fluid Pump - Faulty transmission fluid pump can cause harsh shifts and audible transmission noise. This leads to decreased performance and chances of increased physical damages to the transmission components. Thus, replace it immediately.
6. Electronic Control Unit - Is your car jump starting on reverse polarity? Or are you facing some intermittent starting issues? If yes, then it indicates that your electronic control unit is bad. So it is very important to replace the defective electronic control unit with us at equitable prices.
7. Diagnostic Tools - Buy quality diagnostic tools to check and diagnose OBD code P2701 error with the help of experienced mechanic. Visit us today!
8. Automatic Transmission Filter - A faulty Automatic Transmission Filter can be troublesome. You can always rely on us as we have the best auto parts for our customers.

There could be countless symptoms that would accompany this fault code. Willing to know some common symptoms of OBD Trouble Code P2701? Your wish is our demand. Have a look at them below:

Common Symptoms

• Automatic transmission fluid might start leaking
• Rough handling
• Transmission skidding
• Inconsistent shifting
• Uncommon shift patterns
• Jarring shift selection
• There might be low torque
• Uncertain power output

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Rebuild the mechanical issues in the transmission
• Recondition the quirky transmission control module
• The defective shift solenoid should be mended
• If you find out that there is a stoppage in transmission hydraulics, then it should be replaced or repaired as per the need
• You must fix the less ATF level
• Restore the grubby ATF
• Repair or replace the faulty transmission valve body
• If there is an opened or shorted transmission control module harness, then you must repair it
• Replace the transmission control module circuit

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range tcm, atf, obd2, obd2 scanner, Obd2 bluetooth, car diagnostic tool, car scanner, transmission jack, manual transmission fluid, scan tool, honda transmission fluid, clutch solenoid, atf fluid, auto transmission, transmission fluid pump and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P2701 code to be stored:

• The integrity of your Automatic Transmission Fluid should be verified. You can use the dipstick to check the level of the A/T with the vehicle running and in park. This procedure varies a significant amount between manufacturers. This information can usually be found quite easily with the service manual in the dash or sometimes even printed on the dipstick itself! Just make sure that the fluid is clean and free from debris.
• If you do not remember ever doing a transmission service, it would be a good idea to check our records and service your transmission accordingly. You'd probably be surprised how dirty ATF can affect the functionality of your transmission.
• You should always check ATF level on flat surface to acquire accurate readings. The manufacturer recommended fluid should always be used.
• Generally when you are attempting to search the connector/harness for this system, then you must search for a junction connector.
• There might be one "master" connector, so just be sure that you are working with the right one by referring to your manual. The connector should be seated properly to ensure perfect electrical connection.
• Where the connector is situated on the A/T, it may be subject to vibrations that could cause connections to come loose or physically damage them.
• Not to mention, the possibility of ATF to saturate connectors as well as wires causing future or present problems.
• It is always a great decision to be aware of the overall condition of your automobile. There is a fact that other systems can directly affect other systems.
• Rough tires, worn out suspension parts, wrong wheel, all of these might cause problem in this system and there are some other causes as well. So that’s the reason why it is very important to get rid of this error code.

Common Mistakes When Diagnosing The P2701 Code

• Malfunctioning clutch solenoid
• There can be a failure in the internal transmission
• Transmission control module problems