P2483 OBD Error Code: Problem & Solutions

<<See All OBD Codes

If you notice a lean or risk condition in the engine, decreased fuel efficiency, black smoke from the taillight, and/or illuminated Check Engine Light on the dashboard, them there is a major possibility that you are dealing with the OBD Code P2483 with your vehicle. This code indicates the problem with a particular EGT sensor for bank 1 sensor 5 of the engine.

The EGR temperature sensor is an engine management sensor that is part of the EGR system. It works together with the EGR solenoid to control the flow of the EGR system. The sensor is installed in between the exhaust and intake manifold, and monitors the temperature of the exhaust gases. When the temperature rises, the EGR temperature sensor will send a signal to the computer that will increase the flow in order to reduce pressure and temperature of the system.

When the sensor fails or has any issues it can cause problems with the EGR system, which can lead to failed emissions test and other issues. Usually a bad or failing EGR temperature sensor will produce a few symptoms that can alert the driver of a potential issue that should be inspected.

What causes this problem with the Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 5?

• Dripping in the exhaust
• Unacceptable electrical connection in the sensor 5 bank 1 EGT circuit
• Issue of unbolted sensor 5 bank 1 EGT harness
• Imperfect bank 1 sensor 5 EGT sensor
• Leak detection pump faulty
• Diesel particulate filter not working properly

1. Engine Control Module - Dead cells in batteries can cause a failure in the engine control module. Many times a battery is left in the rig long after a cell has died. This would affect the grounding in the car battery.
2. Powertrain Control Module - If there are some faults in the PCM, then it may throw off the timing and fuel settings of the engine, which can negatively affect the performance. A flawed PCM may cause the vehicle to experience a reduction in fuel efficiency, power as well as acceleration.
3. Exhaust Gas Recirculation Valve – Bad EGR valve can cause many performance issues. Common signs include engine performance issues like decreased power and acceleration, rough idle, and the Check Engine Light coming on. Thus, replace faulty EGR valve now!
4. Diesel Exhaust Fluid Pump – If the DEF pump will not function properly, it can cause increased emissions in the exhaust system and reduced the longevity of the filtration elements in the exhaust system. Thus, replace faulty pump immediately.
5. Electronic Control Unit - Do you know that the poor performance or unexplained drops in fuel economy or efficiency are often associated to onboard car computer problems, or defective ECU issues?
6. Diagnostic Tools – Use factory grade diagnostic tools to resolve OBD code P2483 error. Buy new diagnostic tools and equipment for us.
7. Fluid Pump Control Module – If the control module is faulty, the pump will not be able to work properly and will not be able to transfer fluid to the transmission and hydraulic system efficiently. Thus, replacements are in order.
8. Engine Coolant Temperature Sensor - One major symptom of defective engine coolant temperature sensor is an overheating car engine. This can also cause engine misfiring. Take care of your car engine coolant temperature sensor and replace it if needed.
9. Catalytic Converter - Catalytic converters at fault will lead to dropped fuel efficiency and performance along with increased emissions. Thus replace faulty parts now!
10. Air Filters – Check for clogged and damaged air filters and replace them immediately as it will hamper the air intake systems. Buy new filters now!
11. Diesel particulate filter - A crammed and contaminated diesel particulate filter leads to problem with the functioning of the cooling fans, a slight increase in the fuel consumption and the engine performance. Log into Parts Avatar for your new fuel injectors available at just the right prices.
12. Exhaust Gas Temperature Sensor - Is your engine overheating? Spending too much on gas lately? Well, all this likely to be caused due to your faulty exhaust temperature sensor. So in order to get rid of the error code P2483 and all these complications, change or repair your exhaust temperature sensor now. Tune into Parts Avatar!

If you are facing OBD error code P2483, then there are significant common symptoms that can be felt or observed. We have worked out a list here to help you out in understanding this problem better:

Common Symptoms

• Reduced fuel economy
• Increased exhaust emissions
• Degrading engine performance
• CEL (Check Engine Light) illuminated
• Engine performing abnormally
• Excessive exhaust smoke on load

We have listed out some ways which would help you to correct the occurrence of OBD Code P2483. They are mentioned here as follows:

• You must fix the inferior quality electrical connection
• It is essential to restore the flawed PCM
• Rehabilitate the defaults in the exhaust gas temperature sensor bank 1 sensor 5
• Carefully mend the leakage in the exhaust
• Adjust the flawed wiring

However, if you face any issue then we have stocked a wide range of best priced Powertrain Control Module, PCM, Exhaust Gas Temperature Sensor, Diesel Particulate Filter, Engine Control Module, battery and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this P2483 fault code:

The first and the foremost step is to use a scan tool to inspect for any codes in the automobile’s engine control module. Just keep in mind that there might be some current, pending, or history codes, so it is very important to note all of them. Carefully look at the freeze frame data for each code. After that the codes should be cleared up. Now once you have cleared all the stored codes, the vehicle should be taken out on a test drive to confirm if the check engine light comes back on or not. If you find out that the code is still appearing, then the mechanic must inspect what codes are stored this time. After that a visual inspection of defective or broken components should be performed. Use a scan tool to inspect the bank 1 sensor 5 exhaust gas temperature readings and then it should be compared to the bank 2. Then, use a multimeter to inspect the EGT bank 1 sensor 5 resistance. If nothing else is seen, then it is essential to use a temperature gauge to assess the EGT sensor readings accuracy.

Common Mistakes When Diagnosing The P2483 Code

• Common mistakes while diagnosing this trouble code are unnecessary and expensive replacements which usually happen when one don’t follow all the steps carefully.
• The most common mistake while diagnosing this code is missing out on diagnosing steps which further leads to the expensive and unnecessary replacements. It is always recommended to seek help of experienced diagnostician to avoid any mistakes.