P2482 - OBD Trouble Code

<<See All OBD Codes

The trouble code P2482 can be elucidated as Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 5. The exhaust gas temperature is a heat sensitive resistor which converts the temperature of the exhaust into a voltage signal to the computer. It would mean that the sensor signal voltage is shorted high on bank 1 sensor 5, which would thus indicate that the temperature sensor is out of specified temperature range for a normal exhaust after the particulate filter on diesel engines.

Diesel Exhaust Fluid (DEF) helps in converting harmful exhaust particles to harmless gases. For burning these particles, the temperature of the exhaust system has to be increased. The DEF Fluid with the help of the injector is sent into the exhaust stream to raise the Diesel Particulate Filter (DPF) up to optimal temperature. The exhaust system then convert harmful nitrous oxide compounds to nitrogen, carbon dioxide, and water. This optimal temperature that is needed to convert the harmful emissions to nil, is measured using the EGT sensor and if the bank 1 sensor 5 is not performing, OBD code P2482 gets triggered.

What causes this problem with the Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 5?

• There might be loose or eroded connectors or terminals
• a short directly to ground due to flawed wires
• Some issues related to the defective sensor
• There might be a catback exhaust system without EGT provisions installed
• There can be distorted computer

1. Exhaust Gas Recirculation Valve - Did you just see check engine light flashing on your dashboard? If the computer would detect some fault with the automobile’s EGR valve circuit, then it would set up the check engine light so that the driver is notified about the fault. Don’t waste time and get them replaced or else this fault code can turn up.
2. Diesel Exhaust Fluid Pump - The diesel exhaust fluid pump needs to work properly if the transmission system has to perform. If it is not functioning, the transmission may slip and cause harsh shifts too. Thus replace faulty pump now and buy a new one from us!
3. Engine Control Module - Is your car engine light still staying ON after resetting or your car engine is turning off for no reason? Then these are some common symptoms indicating that your car engine control module is defective.
4. Powertrain Control Module - The PCM works as the central computer system in an automobile’s mechanism. This auto part is the in charge of all the constituents as well as the functions performed by them. Having such enormous importance in the operation of all the parts means that any defect in it will affect almost every aspect of a car.
5. Fuel Injector - If there is a leakage in the fuel injectors, then it might cause rise in the fuel consumption, fuel odours around the vehicle and hard starting. You can always rely on us as we have best auto parts for our customers.
6. Electronic Control Unit - The ECU is a major component of your car's onboard computer. It's used to regulate many systems and subsystems in your car's engine, drive train and other major components. Visit us to buy best quality ECU online.
7. Diagnostic Tools – Take help of a professional mechanic to diagnose OBD code error. Use high grade diagnostic tools to resolve this issue. Buy new tools and equipment form us!
8. Fluid Pump - The fluid pump is usually located in the cover of the transmission. It draws fluid from a pump in the bottom of the transmission and feeds it to the hydraulic system. It also feeds the transmission cooler and the torque converter. Thus, replace faulty fluid pump now!
9. Engine Coolant Temperature Sensor - Did you just see black smoke coming out from your vehicle’s exhaust? Black smoke is an indication that you should not drive your vehicle as there might be some fault in the engine coolant temperature sensor. Buy engine coolant temperature sensor from us online at affordable prices.
10. Heated Oxygen Sensor – A faulty sensor will not be able to perform properly and not analyse the air to fuel ratio in the exhaust. Visit us today to replace damaged oxygen sensors.
11. Diesel Particulate Filter - Love hitting the roads but hate the halts? Well, dirty or jammed diesel particulate filter not only triggers the error code P2482 but also problems like a deactivation of the start/stop button. Now get your error code P2482 fixed right here with us. What are you waiting for? Get your filter changed now.
12. Exhaust Gas Temperature Sensor - Failed emission tests? Engine pings? Check engine light illuminated? Well, all this is caused due to a faulty exhaust temperature sensor. Tune into Parts Avatar to get your error code P2482 fixed just in the right time.

We at Parts Avatar Canada care for our customers, and that’s why we will help you to diagnose P2482 code by listing out some major symptoms. They are mentioned below as follows:

Common Symptoms

• Visibility in the check engine light
• Illumination of the particulate filter light
• There might be low power condition if there is clogged particulate filter

Want to correct the Trouble Code P2482? Read these points mentioned below:

• Repair or replace the quirky sensor after the particulate filter is cleaned
• Rehabilitate the defaults in the wiring or connection to the exhaust temperature sensor assembly
• Carefully adjust the faults in the ECM for a short circuit in the ECM temperature sensor circuit

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Powertrain Control Module, PCM, Exhaust Gas Temperature Sensor, Diesel Particulate Filter, Engine Control Module, fuel shutoff valve, catalytic converters and many more. Now all your problems would vanish within no time.

• After verifying the P2482 code with an OBD-II scanner, the mechanic should begin with a visual inspection of all electrical components, especially looking for some issues in the exhaust gas temperature sensor circuit.
• The code should be scanned and then document the code in the engine control module.
• Then this error code is diagnosed, as per the manufacturer's pinpoint test, to inspect the sensor signal.
• After that the particulate filter cleaning routine is carried out.
• Then carefully retest the sensor.
• The sensor should be disconnected and inspect if the voltage short goes away on the scanner.
• The mechanic should continue checking each possible cause, clearing the code and retesting the system after each attempt, to be sure that the correct solution is found.

Common Mistakes When Diagnosing The P2482 Code

• A big mistake of clearing ECM memory codes before inspecting the freeze frame data of the failure can be made by a lot of mechanics.
• A lot of people make a big mistake of replacing the sensor. Save yourself a big headache and make sure that you are addressing the exhaust restriction after the sensor is causing the excessive back pressure in the exhaust.