Error Code P0A35: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0A35 can be elucidated as Drive Motor "B" Over Temperature Issue. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

Are you tensed because the P0A35 fault code is flashing? We have got everything which you need and at equitable prices. You must visit us and we promise that you will never regret your decision. The drive motor "B" temperature sensor circuit is being monitored by the engine control module. This trouble code would be set by the ECM when the drive motor "B" temperature sensor circuit would not be as per the specifications set by the manufacturer.

What causes this problem with the Drive Motor "B" Over Temperature?

• Issues related to the drive motor A current sensor
• Drive motor B temperature sensor harness unlocked
• Poor electrical connection in the drive motor B temperature sensor circuit

1. Engine Control Module - There can be some issues with the Engine Control Module due to which you may see P0A35 code appearing over and over again. Visit us to buy best quality Engine Control Module online.
2. Powertrain Control Module - A lot of issues can arise do to defective Powertrain Control Module. Did you just see P0A35 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Engine Wiring Connectors - Faulty wiring and connectors are the major reason behind failure of any component and sensor circuit. Buy new wiring connectors now!
4. Electronic Control Unit - Check for ECU faults and replace the components immediately. Buy new ECU components now!
5. Diagnostic Tool - In order to detect the error, one needs high grade diagnostic tools. Visit us today to grab amazing deals.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Visibility in the check engine light
• Non-operational high voltage system

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• You must fix the defective drive motor B current sensor harness
• Make sure to mend the faulty drive motor B current sensor
• It is essential to restore the flawed ECM/PCM
• Rehabilitate the defaults in the drive motor B current sensor circuit
• Carefully adjust the faults in the dash check engine light

However, if you face any issue then we have stocked a wide range of best priced Temperature Sensor, Drive Motor, Motor Harness, Engine Control Module and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• As an initial step the mechanic will carefully inspect the vehicle with the help of a scanner.
• After this, the technician will connect a scanner to the diagnostic code so that he can recover all the codes and freeze frame data.
• Note down this information as it can clearly help for further diagnosis.
• The mechanic will also inspect the shift solenoid to find if it is disconnected or if any other faults persist.
• After careful inspection, he will reset the code and test drive your vehicle to check for reappearance of the codes.
• He will know that an intermittent condition persists, if the code does not return instantly.
• But if the error code returns quickly, the vehicle is test driven, and then he has to inspect the transmission fluid.
• If any of the component is damaged, the mechanic will replace them quickly.
• Most often, whenever the mechanic carries out any repair work, he will reset the code and test drive your car, to check if the codes return immediately. This can preferably help the mechanic to know. what caused this error code in the vehicle?

Common Mistakes When Diagnosing the P0A35 Code

Common mistakes while diagnosing this trouble code are unnecessary and expensive replacements which usually happen when one doesn’t follow all the steps carefully. In this code usually people replace Hybrid Motor Temperature Sensor without even properly diagnosing it. Thus, follow proper diagnostic steps and avoid any chance of misdiagnosis.

• High voltage coolant level is too low
• High voltage water pump failure
• Inverter/converter assembly failure