P0A32 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0A32 can be explicated as Drive Motor "B" Temperature Sensor Circuit Low. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. The engine control module, powertrain control module or the transmission control module monitors this circuit depending upon the particular automobile.

Do you want to gain some more knowledge about the P0A32 trouble code? If the engine control module would detect a variation in the voltage coming from the Drive Motor "B" Temperature Sensor Circuit that is outside the parameters set by the automobile manufacturer, then it would store the P0A32 error code. This would also give rise to the illumination of the check engine light.

What causes this problem with the Drive Motor "B" Temperature Sensor Circuit Low?

• Hybrid Vehicle Motor faulty
• Hybrid Vehicle Motor harness is open or shorted
• Poor electrical connection to Hybrid Vehicle Motor circuit
• Oxygen Sensor failure
• Intake manifold failure
• ECU and PCM faults

1. Engine Control Module - Inspect and replace or reprogram faulty ECM unit. Buy new ECM module from us today!
2. Powertrain Control Module - PCM faults can lead to wrong error getting stored in the system and thus leading to misdiagnosis. Buy new PCM components form us!
3. Electronic Control Unit - If the ECU is damaged, it must be replaced immediately. Buy new ECU now!
4. Oxygen Sensor - Wrong reading by the oxygen sensor will lead to affected combustion and thus the affected engine performance. Buy new oxygen sensor now!
5. Intake Manifold - Check for faulty intake manifold system leading to rich or lean engine conditions and replace it now!
6. Starter Motor - Starter motor can be faulty leading to engine misfires and not starting. Buy new starter motor now!
7. Diagnostic Tools - An experienced mechanic will make use of factory grade tools to diagnose an OBD problem. Buy best tools and equipment from us.

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0A32 here:

Common Symptoms

• Check engine light can start flashing up
• High voltage system not functioning properly
• Engine misfires and stalling
• Lean engine condition

The repairs which you will have to do to correct this fault code are simply straightforward; you can surely pinpoint the necessary repairs on the basis of your diagnosis. Have a look at some common fixes:

• You must fix the defective engine control module
• Restore the flawed drive motor B temperature sensor
• Rehabilitate the defaults in the drive motor B temperature sensor circuit
• Repair or replace malfunctioning drive motor B temperature sensor harness and connectors
• Repair or replace ECU and PCM

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Engine Control Module, PCM, Hybrid Motor Temperature Sensor, Temperature Sensor, Electronic Control Unit, Motor, Engine Light and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• This is a general type of error code which is diagnosed with the help of a scanner.
• The mechanic will insert a scanner to diagnostic port of the vehicle and recover the codes and freeze frame data.
• If he happens to find any additional error codes, he has to address them as well.
• Once it is done, he has to reset the vehicle, and then test drive to see if the error code appears.
• If the error code does not return, then there can be an erratic condition.
• But, if the error code returns, then the mechanic has to check the transmission fluid.
• If the transmission fluid is dirty or if it is below the expected level, it has to be refilled or the dirty fluid has to be replaced.
• Also, the mechanic can check for any sign of leaks, and quickly fix the issue.
• Then the mechanic has to check the wires, connectors and other electrical components and quickly replace them if he finds them to be damaged or defective.
• If the issues are not yet sorted out, then the mechanic will use a digital voltmeter/ ohmmeter and connect it to the vehicle.
• Once the circuit is inspected, he will thoroughly check all the harness and repair them accordingly.
• In most cases, this error code can arise mostly because of any shorted wires or dirty or contaminated transmission fluid.
• Whenever the mechanic or a trained professional, repairs any of the component like wires or connectors, he will reset the code and test drive the vehicle again to see if the error code appears again.
• This can actually help the mechanic to know if the problem is fixed.

Common Mistakes When Diagnosing the P0A32 Code

A lot of people make a big mistake of attempting to diagnose the hybrid motor temperature sensor directly. Save yourself a big headache and make sure that you are doing proper analysis and checking each component step by step before coming to any conclusion.

• Check for faulty wiring and connectors
• Faults in the Motor Temperature Sensor
• ECU and PCM fault checks