P0932 - OBD Trouble Code

<<See All OBD Codes

You’re having the P0932 code flashing and you don’t know what it means! Well we have you covered in not just understand what it means but also how to resolve it. This is a standard OBD-II code and hints an issue with the electrical system in the hydraulic pressure sensor. This hydraulic pressure which is monitored by the PCM via the hydraulic pressure sensors, when an error in signal is noticed by the PCM it will set P0932 code.

The P0932 is typically caused because of defective electrical components, like a short circuit or corroded cables, damaged wires, blown fuses etc. Loss of ground can also be a reason. This code can also be set due to a faulty hydraulic pressure sensor or failure of the PCM/TCM. So, when it comes to resolving it, the diagnosis requires a thorough look at all of these components to rule out who is causing it.

What causes this problem with the Hydraulic Pressure Sensor Circuit?

• Defective electrical components such as wires, connectors and switches
• Fault in the hydraulic pressure sensor
• Malfunctioning PCM or TCM.

1. Electrical Components - Repair all the damaged parts, if that’s not helping with the P0932 code, then you will have to opt for replacement. Parts Avatar has you covered with a wide variety of parts. Order online today!
2. Fuse - Mend the damaged fuses and accordingly check if replacement is needed. You can find the perfect replacement part online with us, simply place order from the comfort of your home and track it easily till it reaches you.
3. Hydraulic Pressure Sensor - Simply replace the sensor and its components and get rid of the P0932 code.
4. Powertrain Control Module - Repair and check if the P0932 code still persists, if it does you will have to replace the PCM. Buy from Parts Avatar from the comfort of your home and avail free shipping on order over CAD $99.
5. Transmission Control Module - Check for repairs or opt for replacement from us. We have the best quality products for you. Order today and have it shipped right to your doorstep in just few days!

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0932 here:

Common Symptoms

• Check engine light is on
• Issues with transmission
• Harsh shifting and inability to access some gears
• Low fuel efficiency

Here are some ways with the help of which you will be able to correct the OBD Code P0932

• Repair or replace all the damaged wires, connectors, and fuses
• Repair or replace the Hydraulic Pressure Sensor
• Repair or replace the PCM or TCM

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade Electrical Components, Blown Fuses, Hydraulic Pressure Sensor, Powertrain Control Module, Transmission Control Module and a lot more for our precious customers.

Here are some steps which you should follow in order to diagnose this fault code:

• You will have to use the standard OBD scanner to diagnose P0932 code. Connect the scanner to the diagnostic port and retrive all the codes, solve them in their order after freeze framing the data. Reset the codes and take your vehicle on a test drive and see if the code is reset or not, if it’s not, it’s because the code was most likely due to an intermittent condition. Intermittent conditions typically have to worsen before the correct diagnosis can be made.
• If the P0932 code is reset, then you will have to start a very thorough visual inspection of the electrical components of the system. All the damages wires, connectors, and or fuses will have to be repaired or replaced depending on the extent of damage. You will also have to inspect if there’s ground voltage. If you find that no issue is present, then you could suspect the problem being with the hydraulic pressure sensor. Inspect it properly too and try to repair the issues.
• After replacement is done, reset the codes and restart the vehicle and note if the code returns. It’s better to do this after each step of repairs and replacements so that time is not wasted and you will know as soon as the issue has been resolved.

Common Mistakes When Diagnosing the P0932 Code

• Not following the OBD-II diagnosis protocol correctly
• Replacing the hydraulic pressure when it was working instead of repairing the defective wiring.