Error Code P0925: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0925 can be defined as Gear Shift Reverse Actuator Circuit Range/Performance. One thing which you must keep in mind that its symptoms as well as causes would surely vary as it depends upon a number of things. P0925 code would start appearing when there would be an unusual voltage reading from the gear shift reverse actuator circuit due to quirky reverse gear guide rail or shift shaft. It would also give rise to the appearance of the check engine light.

It is always good to learn more! That is the reason we are here to help you out in gaining more knowledge about the P0925 error code. It is a generic OBD-II trouble code which depicts an issue with the transmission gear shift reverse actuator circuit. The gear shift reverse actuator is responsible for sliding the transmission into the reverse gear. Now if an unusual voltage reading from the gear shift reverse actuator circuit would be detected by powertrain control module, then it would trigger up the P0925 fault code.

What causes this problem with the Gear Shift Reverse Actuator Circuit Range/Performance?

• There can be inoperative reverse gear guide rail or shift shaft
• Imperfect PCM, ECM, or transmission control module
• Some issues related to the gear shift reverse actuator
• There can be some mechanical problems within the transmission
• Quirks in the electrical components in the system like shorted wires or corroded connectors

1. Speedometer - Did your mechanic just found out that there is some fault in the Speedometer? Buy top notch Speedometer from us at economical prices.
2. Powertrain Control Module - A broken Powertrain Control Module can cause a lot of issues. It would be nice if you get it replaced on time.
3. Car Battery - Everything is fine with the engine control module and still OBD code P0925 flashing? Then there is definitely some fault with the Car Battery. Get it checked and replace if needed.
4. Engine Control Module - Engine Control Module is an important car part which should never be neglected. May be there is some fault in it due to which P0925 code may start flashing.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0925 code by mentioning some major symptoms below:

Common Symptoms

• Visibility in the check engine light
• Problems related to shifting into or out of the reverse gear
• Lower fuel efficiency

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0925:

• You must fix the defective PCM
• Make sure to mend the faulty shift shaft
• Carefully adjust the faults in the gear shift reverse actuator
• The transmission control module should be restored to working order
• Recondition the non-functioning reverse gear guide rail

However, if you face any issue then we have stocked a wide range of best priced speedometer gauge, gauge cluster, ECM module and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

An advanced scan tool should be used so that you are able to read the ECM data value. A digital voltage meter with attachments is to be used. A scanner should be used by a professional technician to notice the freeze frame data, to assemble details about the code. The mechanic can also check to see if there is presence of additional trouble codes. Now if there are a number of codes, then they should be addressed in the same order in which they are appearing on the scanner. The wiring, connectors as well as other constituents should be properly diagnosed for any default. Then clear the P0925 fault code and the entire system should be tested properly to check if the code returns. Now if you find out that the code is returning back again, then you should use a digital volt/ohm meter to inspect the voltage and ground signal at the gear shift actuator switch. If you find out that no voltage or ground signal has been detected, then the PCM should be disconnected by the mechanic as well as other associated modules.

The continuity between the gear shift actuator switch and the battery ground should then be tested. Then carefully examine the shift shaft as well as the forward guide rail for some faults and just make sure that they are functioning in the right manner. The P0925 fault code should then be cleared by the mechanic to check if the code is appearing again or not. If there is an appearance of the code, then the TCM should be inspected properly for defects. If everything is fine with the TCM, then the technician should check the continuity of the PCM to have a look if it has some flaws. Now whenever the mechanic replaces the constituent, then he should stop the checking and then reset the error codes. The vehicle should be restarted once again to check if the code is still appearing. It would assist the technician to know as soon as the P0925 error code has been reconciled.

Common Mistakes When Diagnosing The P0925 Code

• The most common mistake while diagnosing this code is missing out on diagnosing steps which further leads to the expensive and unnecessary replacements. It is always recommended to seek help of experienced diagnostician to avoid any mistakes.
• If it is not done properly, then the codes would be addressed in the incorrect order. Due to this a simple fix would be missed and at the same time codes would not be cleared.