P0914 OBD Error Code: Problem & Solutions

<<See All OBD Codes

Error code P0914? No worries, We have got you covered! A P0914 trouble code is generic code that is stored when there is an electrical error identified in the gear shift position circuit. Also, when the voltage coming from the gear shift position sensor fails to fall within the manufacturer's specifications, the check engine light is illuminated and the trouble code P0913 is set.

It can be registered that manual transmissions have a sensor installed on the shift lever that determines and informs the engine computer (PCM) about what gear the transmission is in. If the PCM receives a dubious signal by the shift lever position sensor, code P0914 is stored. It is usually the shift lever assembly which accommodates the shift lever position sensor.

What causes this problem with the Gear Shift Position Circuit?

Broken or faulty wiring, connectors, or elements within the gear shift position system are the most common reasons triggering a storage of the P0914 trouble code. Other causes that may lead to the storage of this code are blown or burnt fuses, a short to the battery ground, and a malfunctioning PCM.

1. Gear Shift Position Circuit - Errors in the gear shift position circuit can always be problematic. So, it is recommended to fix the errors instantly.
2. Powertrain Control Module - Abbreviated PCM; this is an integral control unit. So, a defective one should be changed immediately.
3. Shift Lever Position Sensor - Having problems with the shift lever position sensor? Don’t you worry, Parts Avatar has it all. An erroneous shift lever position sensor could end up being the root cause behind the error code P0914.
4. Wiring Connectors - Weary and damaged wirings and connectors can often be problematic. So, to add some spark to your ride you definitely need the perfect quality wirings and connectors offered at Parts Avatar. Isn’t that just the perfect deal?
5. Shift Gears - A distorted shift gears can end up being the chief host inviting the error code P0914. So, replacing one can be one of the wisest decisions to avoid a problematic system.
6. Volt/Ohmmeter - Get your error code fixed instantly with a new volt/ohmmeter. Parts Avatar right place that provides the best volt/ohmmeters across the country.

We at Parts Avatar Canada care for our customers, and that’s why we will help you to diagnose P0914 code by listing out some major symptoms. They are mentioned below as follows

Common Symptoms

Generally, the symptoms that trigger a P0914 trouble code include irregular shifting and in some specific cases the inability to shift gears. Another common side effect of a P0914 trouble code is a reduction of the fuel efficiency in the vehicle that leads to setting up of this error code.

Learn the ways with which you can correct this trouble code:

To repair a P0914 trouble code, a mechanic should take the following steps after diagnosis:

• All the distorted or corroded wiring, connectors, or components should be replaced
• If the gear shift position circuit is malfunctioning it should mend
• The shift shaft if damaged or not working in order should replace or repaired
• A defective gear guide rail should be replaced if required
• A faulty PCM should be changed or mended. The PCM would require reprogramming before installation

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of gear shift position circuit, pcm, shift lever position sensor, shift gears, volt/ohmmeter, car stickers, car gears, automatic gear shift, and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0914 code to be stored:

• To diagnose and repair a P0914 trouble code a mechanic needs to use an advanced scanner and a digital volt/ohm meter. Using this equipment, the mechanic needs to perform the following:
• All the wirings, connectors and components should be thoroughly inspected for any signs of damage.
• The codes should be cleared and the vehicle should be test driven see if the code reappears
• All the freeze frame data should be downloaded and all the stored codes should be stored so that it can be used in further diagnosis.
• The technician should next proceed to test the voltage and ground signal at the gear shift position circuit Using a digital volt/ohm meter.
• The PCM and the other related control modules should be disconnected, if no voltage or ground circuit is disconnected. Next, the continuity of the gear shift position circuit along with the battery ground should be tested too.
• The technician should investigate the shift shaft to see if it is operating as per the specifications, if the code returns after clearing.
• The gear guide rail should be inspected for any signs of damage by the technician.
• If all appears to work in order, an erroneous PCM should be suspected.
• The PCM should be inspected and examined to see if it is damaged or just needs a mere reprogramming.
• Lastly, the codes should be cleared and the system should be retested to see if the code persists.

Common Mistakes When Diagnosing the P0914 Code

Here listed are a few common mistakes that should be avoided while diagnosing the error code P0914:

The most common mistake committed by the technicians diagnosing the error code P0914 include the replacement of the entire gear shift position system while the problem could be solved by just replacing a minor electrical component, connector or wirings. Apart from this, failing to clear the code as they are stored can also lead to failing to completely solve the problem causing it to reappear again.