Guide To P0834 OBD Error Code Solutions

<<See All OBD Codes

Is the car engine cranking up and not starting? Did the engine start even when the car was in gear? Is the engine not starting even when you have engaged the clutch? All these are an indication of problematic Clutch Pedal Switch Circuit problem thus leading to P0834 error code getting stored in the system.

The Clutch Pedal Position Sensor tells the powertrain control module (PCM) that the clutch pedal is depressed. When the PCM detects an incorrect signal from the Clutch Position Sensor, the PCM will set code P0834.

The clutch sensor switch determines the clutch position and only allow the engine to start when its circuit in complete by engaging the clutch pedal and ensuring that the vehicle will not start in gear. It always has current flowing from one end of the circuit, waiting for the circuit to get complete and sending it to the starter to start the engine. When the PCM notices low voltage at that end, it stores and flashes P0834 error code and may illuminate the malfunction indicator light.

What causes this problem with the Clutch Pedal Switch "B" Circuit Low?

• Faulty Powertrain Control Module
• Failed Clutch Pedal Position Sensor
• PCM/TCM programming error
• Open or shorted circuit or connectors in the CPS harness
• Failed PCM/TCM power source
• Worn out wires and connector to the sensor and circuit
• Insufficient control module ground

1. Diagnostic Tool - Use factory grade diagnostic tools to detect and diagnose the problem properly. Explore from wide variety of tools and equipment form us. Buy today!
2. Powertrain Control Module - PCM faults or incompatibility with the PCS will cause drivability and performance issues. Repair, replace or reprogram it as required.
3. Clutch Position Sensor Switch - If the CPS switch is faulty and the output voltage to the starter is low, the OBD code will flash. Buy new CPS switch now!
4. Clutch Connector - Inspect for the corroded or damaged connector to the sensor circuit and replace it now!

For us our customers are everything, and that’s why we will help you to diagnose P0834 code by mentioning some important symptoms below:

Common Symptoms

• Malfunction indicator light on
• Engine not getting started
• Engine start without clutch engaged
• OBD code stored in the system

We have listed out some ways which would help you to correct the occurrence of OBD Code P0834. They are mentioned here as follows:

• Replace Clutch Position Sensor (CPS) switch
• Damaged wiring and connector to the sensor and circuit
• PCM repairs or reprogramming
• Blow fuses replacement

However, if you face any issue then we have stocked a wide range of best priced Clutch Position Sensor Switch, Fuses, Clutch Position Sensor Connector, Fusion, Clutch Pedal Position Switch Harness, Powertrain Control Module more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• Use the OBD scanner and retrieve all the coded and freeze frame the data. After doing that test run the vehicle again under same circumstances to see if the code returns to make sure which codes are persistent.
• Inspect for any damaged, or corroded wiring and connector issue and repair or replace them as required. Also check for blown fuses and replace them immediately.
• Check for the output voltage to the starter solenoid. If there’s no output voltage, check for the sensor switch to the sensor circuit. If the output voltage is missing even when the clutch in engaged, then the sensor switch might be faulty and might need replacement. Also, when the output voltage is low, then the PCM will flash P0834 error code in the system.
• It is important to recheck the system after doing all the replacements. Check for the proper functionality of the position sensor in accordance with the clutch pedal as well as the proper transfer of input to output voltage reaching to the starter solenoid and thus leading to starting of the engine.
• It is also important to disconnect all other related control modules before rest the position sensor functionality to avoid other codes getting stored in the PCM.
• Lastly, check for the faults in the PCM as it might a case where, it’s storing the wrong OBD code error which everything is working perfectly. Thus, it might need replacement and reprogramming as well.

Common mistakes while diagnosing P0834 code

• Faulty wiring, connectors and fuses to the Clutch Pedal Position Sensor Circuit
• Faulty Clutch Position Sensor harness or connector
• Faulty CPS Switch
• Faulty Powertrain Control Module