Error Code P0832: What It Means & What To Do?

<<See All OBD Codes

This trouble code is generic, which means that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another.

This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code and happens with manual transmission system only.

A P0832 code means that the powertrain control module recognizes a malfunction in the clutch position sensor circuit. It should appear only in manual transmission vehicles. Should it record in an automatic transmission vehicle, it is a sign that the PCM is malfunctioning. When the P0832 error code appears, it signifies an OBD-II generic code describing abnormal voltage and/or resistance coming from the clutch position sensor circuit. This means that the starter is unable to engage. Whenever there is a high voltage scenario in the clutch position sensor circuit, P0832 gets stored in the PCM.

What causes this problem with the Clutch Pedal Switch "A" Circuit High?

• Bad CPS (Clutch Position Sensor)
• Malfunctioning CPS switch circuit
• Electrical connection poor
• Lose control module strap or busted ground wire
• Corroded, shorted or open connectors or wiring in the CPS harness
• Electrical connector corrosion/damages
• Defective CPS harness
• Powertrain Control Module failure

1. Diagnostic Tools - An experienced mechanic will make use of factory grade tools to diagnose an OBD problem. Buy best tools and equipment from us.
2. Powertrain Control Module - P0832 error code also relates to problems with the powertrain which is a combination of engine control module and the transmission control module. Find all the Powertrain related parts with us.
3. Clutch Position Sensor Switch - CPS switch can be faulty giving no passage for the voltage to pass to the starter solenoid to start the engine. Thus, replace it now!
4. Clutch Connector - Sometimes the connectors to the sensor and the circuit are damaged causing disruption is the functionality. Buy new clutch connector now!

We at Parts Avatar Canada care for our customers, and that’s why we will help you to diagnose P0832 code by listing out some major symptoms. They are mentioned below as follows:

Common Symptoms

• Illumination of Malfunction Indicator Light
• Engine not starting
• Engine starting even with clutch engagement

We have listed out some ways which would help you to correct the occurrence of OBD Code P0832. They are mentioned here as follows:

• Make sure to mend the faulty wiring and connector
• It is essential to restore the flawed CPS switch
• Repair or replace the quirky Clutch Position Sensor
• Rehabilitate the defaults in the Powertrain Control Module

However, if you face any issue then we have stocked a wide range of best priced Clutch Position Sensor Switch, Fuses, Clutch Position Sensor Connector, Fusion, Clutch Pedal Position Switch Harness, Powertrain Control Module more to help you out in fixing your car.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0832 code to be stored:

• Always take the help of an experienced mechanic who will visually inspecting the Clutch Position Sensor, searching primarily for the connection faults.
• Inspect for any wiring and harness issues and correct the damaged wirings and repair or replace then to the earliest. Always retest the vehicle after every step of diagnosis to see if the code returns or not. Most of the problems get resolved by replacing faulty wiring and connections.
• Remember to remove all the other modules while performing the diagnosis on the next problem.
• Inspect the input voltage in the CPS switch circuit with the clutch pedal disengaged. If the voltage is not present, doubt for CPS switch failure.
• Now, engage the clutch and look for the presence of an output voltage to the starter solenoid. If not present, the CPS switch is faulty.
• Next, check for the desired range for the voltage passing through the sensor switch circuit. In this case, if the voltage is high, the P0832 code will get stored in the PCM.
• Also check for the failure due to Faulty Powertrain Control Module and replace and reprogram as required.

Common mistakes while diagnosing P0832 code

A lot of people make a big mistake of attempting to diagnose the wrong parts like the ignition system and the starter solenoids. Save yourself a big headache and make sure that you are addressing the correct part before beginning your diagnosis. Always check for faulty wiring and damaged connectors first.