Error Code P082E: What It Means & What To Do?

<<See All OBD Codes

Stressed? Constantly see the error code P082E flashing? Well we have got you covered. Here's how you can treat the error code P082E. The OBD-II code P082E is triggered when a PCM malfunctions. This powertrain control module failure is defined as a gear lever x position sensor circuit low. The engine computer is constantly updated by the gear lever position sensor about the gear the transmission is in. this sensor is usually found in the shift lever. The code P082E is stored when an improbable signal is received by the PCM sent to it by the gear lever sensor.

The code P082E is triggered when the PCM receives an impractical signal from the gear lever position sensor. Also, the engine computer (PCM) is informed about what gear the transmission is in by the gear lever position sensor. Into the Shift Lever, one can see the sensor installed.

What causes this problem with the Gear Lever Y Position Circuit Low?

• A damaged gear lever x position sensor
• The harness in the gear lever x position sensor is loose or shorted
• Bad electrical connection in the gear lever x position sensor circuit

1. Transmission Parts - Still facing problems? Well, a lot of problems can arise due to a malfunctioning transmission. In order to get your error code solved, repair or replace the transmission as soon as possible.
2. Sensor - A faulty sensor can end up being the chief host inviting the error code P082E. So, replacing one can be one of the wisest decisions to avoid a problematic system.
3. Powertrain Control Module - Abbreviated PCM; this is an integral control unit. So, a defective one should be changed immediately.
4. Fuel Metering - anxious about the error code P082E reappearing? Well, it can be due to an error in the fuel metering. Perform amendments instantly.
5. Engine Timing Parts - A bad engine timing should be fixed to fight the error code P082E.

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P082E here:

Common Symptoms

• A transmission shift shock
• An illuminated engine light (or the service engine soon warning light)

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P082E:

• A malfunctioning gear lever x position sensor should be replaced or repaired.
• All the wirings and harnesses should be inspected. Al the corroded ones should be replaced or repaired.
• Amendments should be performed to fix a weak electrical connection running in the gear lever x position sensor circuit.

However, if you face any issue then we have stocked a wide range of best priced transmission, sensor, PCM, fuel metering, engine timing, fuel injectors, fuel injector harness, body control module, injection pump, fuel injection kit, fuel injection tester, fuel injection conversion kit, diesel fuel injectors, transmission control module, electronic control module, brake control unit, performance fuel injectors, engine control unit, engine harness and more to help you out in fixing your car.

Related code: P0821, P0823, P0824, P082A, P082B, P082C, P082D and P082F

Willing to diagnose the error code P082E accurately? Well, here listed are few steps that will definitely help you to diagnose the error code P082E

To start with, the technician will make use of a scanner (code reader) or a digital ohmmeter that are the two basic diagnostic tools that are extremely important for a precise diagnosis of the code P082E. The role of determining the gear the transmission is placed in is played by the transmission range sensor. If by any chance, the voltage appears to absent, then a circuit issue should most likely be examined and observed. The consequences of which can lead to a weak or poor electrical connection. It could trigger because of either an open in the ground or battery voltage for which a digital volt/ohmmeter should be utilized to check for continuity and resistance in both the circuits. All the corroded, damaged or loosened electrical components can lead to worsening the code as well as the system. While diagnosing it is advised to refer to manufacturer’s specification manual. Also, in order to ensure a precise diagnosis, the system should be retested and the vehicle should be test driven in order to make sure the code has vanished completely.