Guide To P079C OBD Error Code Solutions

<<See All OBD Codes

The trouble code P079C can be described as Transmission Friction Element "C" Slip Detected. The amount of force which is required to help the vehicle steering when the ignition is ON and the supply of the voltage to the PSCM is above 6 volts, all other electric power-assisted steering sensors are operating accurately and the EPAS gear is providing assist is observed by the power steering control module.

Don’t worry if P079C error code is triggering again and again. We offer wide range of auto parts at affordable prices to our dear customers. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

What causes this problem with the Transmission Friction Element "C" Slip Detected?

• Flaws in the transmission control module
• Stained ATF
• There can be some quirks in the engine control module
• Problems related to wiring
• Issue of unequal tire sizes
• There can be less ATF
• The friction element might be worn out
• There can be unbalanced rotational speed/circumference
• Issue of water damage to module as well as harness

1. Powertrain Control Module - Do you remember when was the last time you got your car Powertrain Control Module checked up? A flawed Powertrain Control Module can cause a lot of issues like displaying P079C code.
2. Automatic Transmission Filter - Poor Automatic Transmission Filter can cause a lot of difficulties, so why not get it replaced at time?
3. Automatic Transmission Fluid - Are there some faults in your Automatic Transmission Fluid? Don’t waste time and get them replaced or else P079C code can turn up.
4. Body Control Module Component - OBD Code P079C can appear because of faulty Body Control Module Component.
5. Electronic Control Unit - Everything is fine with Automatic Transmission Fluid and still P079C code triggering? Then you must get your Electronic Control Unit checked.
6. Engine Control Module - There can be some issues with the Engine Control Module due to which you may see P079C code appearing over and over again. Visit us to buy best quality Engine Control Module online.
7. Auto Transmission Control Module - A lot of issues can arise do to defective Auto Transmission Control Module. Did you just see P079C code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P079C code by mentioning some major symptoms below:

Common Symptoms

• Deviant power output
• Uncommon shift patterns
• Transmission skidding
• Grinding shift selection
• Unequal handling
• Dripping automatic transmission fluid
• Decrease in the torque
• Inconsistent shifting

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P079C:

• Make sure to mend the quirky electronic control unit
• Carefully adjust the faults in the powertrain control module
• Repair or replace the faulty automatic transmission filter
• You must fix the defective automatic transmission fluid
• It is essential to restore the flawed automatic transmission control module
• Mend the defects in the engine control module
• It is essential to restore the flawed body control module component

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Module, Friction Elements, Diagnostic Trouble, Transmission Oil, Pcm, Atf Fluid, Ecm Module and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• It would be a great idea to start with a technical service bulletin search for your particular vehicle. Advanced diagnostic steps become very vehicle specific and may require the appropriate advanced equipment and knowledge to perform accurately.
• Here are some basic steps below but refer to a vehicle year/make/model/powertrain specific repair guide for specific steps for your automobile. The general maintenance procedures should be carried out on a regular basis, as far as the transmission's health goes, start at the fluid.
• Your automatic transmission fluid should be fully clean, free of debris and also, proper maintenance schedules have to be followed to avoid more defects. If you don’t remember the last transmission has been serviced, it would be a nice idea to perform this before continuing. There might be a bit of debris in your oil that is trapped internally. It may only take a simple service, so you must remember the last time you got your A/T service done.
• You will have to search for a junction connector while you are trying to find the connector/harness for this system. There may be one "master" connector so just make sure that you are working with the right one by referring to your manual.
• Just be sure that the connector itself is seated properly to ensure a perfect electrical connection. Now when the connector is situated on the A/T, it might be subject to vibrations that could cause connections to come loose or physically damage them. The possibility of ATF to saturate connectors and wires causing future or present issues.
• The overall condition of your vehicle matters a lot, and that is the reason why we should be fully aware regarding it. Uneven tires, tattered suspension parts, incorrect wheels, all of these can and will cause problems in this system and possibly others as well. So, make sure that you repair or replace the faulty parts and then this trouble code would stop appearing

Common Mistakes When Diagnosing The P079C Code

• There can be some faults in the internal transmission
• Negligence in the transmission valve body solenoid
• Transmission fluid level might be less