Guide To P0713 OBD Error Code Solutions

<<See All OBD Codes

What cause the error code to be stored in your vehicle? This is a general error code related to automatic transmission temperature sensor. If the code is found, the TCM will read voltage that is very high which means the component is too hot.

This is a general type of trouble code, which indicates that there is a problem of voltage with the automatic transmission temperature sensor. As the temperature increase, the voltage will increase which triggers the P0713 error code. When this code is triggered, the TCM will read that the voltage is high for the manufacturer’s parameter which means the component is too hot. At times, it will also indicate an open in the circuit.

What causes this problem with the Transmission Fluid Temperature Sensor A Circuit High Input?

• Deficient TFT sensor.
• Transmission issue.
• Wire problems.
• Imperfect PCM.

1. Transmission Fluid Temperature Sensor - If you find any injuries or leakages in this component change them immediately.
2. TCU - Is your transmission control unit damaged? Looking to replace them? Grab them at affordable cost from Parts Avatar to avoid P0713 error code.
3. Torque Converter Clutch - Visually look at this element and see if there are injuries. Replace them as soon as possible.
4. TBS - Technical service bulletin can help in careful diagnosis of your vehicle. If there are damages replace them soon.
5. ECM - A broken engine control module needs to be repaired immediately to avoid P0713 error code.
6. PCM - The powertrain control module can be the default component which gives rise to this error code. Replace them if broken.
7. Transmission Fluid Temperature Sensor Connector - Is your connector broken? Never worry. Find the right part from Parts Avatar for your vehicle.
8. Transmission Fluid Temperature Sensor Terminal - If the terminals are damaged, replace with a new one from Parts Avatar.
9. Transmission Temperature Sensor Circuit Wiring - A dripping or shorted wires have to be traded immediately with new one to avoid system malfunction.

Well, it is extremely essential to know the symptoms of the problem in order to detect it. Keeping this in mind, let’s throw some light on few common symptoms of OBD error code P0713.

Common Symptoms

• Engine light is illuminated.
• Improper torque converter clutch operation.
• Prolonged shifts.
• Vehicle shut in in limp mode.

After you know the symptoms of your vehicle’s problem, it becomes easy to detect it and get started with solving it. So, next on our list is few common steps to correct this issue with your vehicle’s.

• Check the transmission for leaks. If the fluid is less, refill it and check the monitor id codes return.
• If there are no leaks and fluid level is good, check the temperature sensor and repair the damaged wires.
• If the error still exists, you have to replace the component.

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of Transmission Fluid Temperature Sensor, TCU, Engine Light, Torque Converter Clutch, TBS, ECM, PCM, Transmission Fluid Temperature Sensor Connector, Transmission Fluid Temperature Sensor Terminal, Transmission Temperature Sensor Circuit Wiring, Transmission Fluid and a lot more. We are sure that now all your issues would be resolved.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

• Visually scan the TFT sensor and its wires. See if there are any broken wires and repair them as desired.
• Inspect your TSB for this issue, else you have to carry out a step by step diagnosis process. In order to carefully diagnose you have to use the diagnostic flow chart listed by the manufacturer.
• Carry out a preliminary test. Using a scan tool, you have to monitor few parameters. Now detach the TFT sensor and attach jumper wires across them. If the scan tool shows high temperature, then the connections are better and they can identify the input.
• The main problem lies with the sensor and so test the sensor. Inspect the resistance between the terminals with DVOM setting to ohms. Start the engine and the value should fall and as it warms. If the temperature increase and the TFT resistance does not decrease, then component has to be altered.
• Inspect for reference signal and if not present connect it to the meter on the PCM. You will see an opening if the meter reads out of limits between the PCM and the sensor which needs mending.
• A numeric value in the meter, indicates it is good. Check for 5 volts from the PCM at reference voltage terminal, if not so, the PCM is faulty. Check for proper ground circuit and attach it to the meter between TFT sensor and the ground terminal.
• An opening will be found if the meter reads out of limit. Finally check for proper ground by connecting the PCM ground terminal to the chassis. If it reads out of limit, then there will be an opening and it needs fixation.
• If everything is good, there can be an issue with the transmission. This especially holds true as the fluid temperature codes are set with other transmission codes.

Common mistakes when diagnosing the P0713 code

Centered on the condition of transmission fluid, the P0713 error is stored based on prior issue. It is well to clear the code, before further troubleshooting to ensure the code does not return.