Error Code P064A: What It Means & What To Do?
OBD Code P064A - Fuel Pump Control Module
Do you know what this code P064A refers to? A decreased engine
performance refers to a Fuel Pump control module, which controls the fuel pump
based upon the request of the Engine Control module. This is a general type of
trouble code which is applicable to OBD- II vehicles. Although it’s a common
trouble code, the repair steps will vary depending on your vehicle’s make and
make and the year it was manufactured. If the PCM (Powertrain control module)
is functioning ineffectively, then the P064A code will be set.
Learn More About OBD Error Code P064A
If the P064A code is stored in your vehicle then it means that the
fuel pump control module is malfunctioning. It is responsible for the proper
supply and circulation of voltage to the fuel pump and fuel pump relay. The
fuel pump controller is a stand-alone module but it can also be integrated into
the PCM. Pressurized fuel is sent into the fuel injection system by the fuel
pump which is located inside the fuel tank. The PCM energizes on the start of
the ignition, and multiple controller self-tests are carried out. By carrying
out these tests, the PCM can examine the serial data which is carried over the
Controller area network (CAN) to make sure that the on-board controllers are in
line.
What causes this problem with the Fuel Pump Control Module?
- Damaged fuel pump controller or PCM
- The voltage supply circuit of the fuel pump control module is open
- The voltage shut off switch of the fuel pump is bad or tripped
- Error in the PCM programming
- The fuel pump control circuit is open or shorted
Replace/Repair These Parts To Fix OBD Code P064A
- Fuel Pump
Control Module - Check for any
openings or damages in the fuel pump control module. If you come across any,
replace them or fix the issue.
- Fuel Pump Harness - If there are any
broken / shorted / open joints they have to be fixed immediately.
- Fuel Pump - A faulty or defective fuel pump can give rise to the P064A error
code. Get the right replacement part for your vehicle from Parts Avatar.
Symptoms Of OBD Error Code P064A
Interested in knowing the symptoms to old code P064A? If yes, then
you have arrived at the right place. We at Parts Avatar have listed out few
common symptoms associated with Fuel Pump Control Module.
Common Symptoms
- The engine delays when you try starting it
- There is no availability of start condition
- Drivability issues in the engine
- Other codes that are stored
How To Correct P064A Fuel Pump Control Module
Have a look at some ways with which you can correct the P064A
code:
- Replacing the fuel pump control circuit / harness
There is no need to get stressed if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Fuel Pump, Fuel Pump Harness and many more. Now all your problems would vanish within no time.
- Chevrolet
- Ford
- Dodge
- Pontiac
- Mazda
- Acura
- GMC
- Toyota
- Volvo
- Nissan Datsun
- Hyundai
- Chrysler
- Kia
- Buick
- Honda
- Cadillac
- Saturn
- Mitsubishi
- Volkswagen
- Hummer
- Infiniti
- Audi
- Subaru
- Jeep Truck
- Suzuki
Easy Diagnosis Of Engine Error OBD Code P064A
Here are some steps which you should follow in order to diagnose this P064A fault code:
- First
you have to connect the scanner to the diagnostic port of the vehicle and
retrieve all the codes that are stored and freeze frame data. Write down this
code, as it can be an irregular connection. Once all the relevant information
is recorded, test drive your vehicle again, until it is reset and PCM is ready.
- It
will be difficult to diagnose if the PCM enters the readiness mode as it is
irregular. The reason which allowed the P064A code to be stored has to worsen
before an accurate diagnosis is made. Continue the diagnosis if the code
resets.
- With
the help of vehicle information, you have to obtain the connector face views,
connector pinout charts, component locators, and diagrams of wire and
diagnostic flow charts which relates to the code.
- If
the fuel pump control circuit has no voltage or ground (though all the fuses
and relays function normally) then you have to visually inspect the controller
related wires and joints. You can also check the engine ground junctions and
chassis. With the help of your vehicle
information gather info on circuits related to ground locations.
- If
both the voltage and ground is available in the fuel pump control circuit,
check the system controller if there are any signs of water, collision damage
and heat. If there are any damages in the controller, then it can be defective.
Common Mistakes When Diagnosing the P064A Code
- The
fuel pump control module has failed
- Powertrain
control module has failed
- Issues
in wiring