Things You Should Know About Car LED Strips

Are you searching for some information about LED Strips? Then wait no more as you have arrived at the right location. Here you will find everything you want to know about LED Strips. Keep on reading further. One of the most common sources of light are the LED strips as they would last for a long period of time and then very little energy would be used in comparison to incandescent bulbs. These strips are very versatile as you can place them anywhere where ever you will have an electrical connection. If you want to add a little bit of extra lighting under cabinets or in your car, then you can easily install LED strips.

Let us understand the basic working of the car LED light strips. It is the 12V supply which would power the light strip controller which then drives each light strip with separate red, green, and blue on/off waveforms. It is with the help of these waveforms that how brightness and colour combinations become possible. There is a need of resistors so you can limit the amount of current which would be received by each LED segment.

The main purpose of the LED light strips is that it is worked by being driven by a special power supply which would then control the amount of time as well as which colour LEDs switch on and off.

If you want to repair your LED Strips all by yourself, then let’s face it that you will need some auto body tools. You can always start by building your own tool chest. Searching for some tools needed to repair your LED Strips? Don’t Worry! We are here to help you out. Here are some common tools that you will probably end up needing while repairing your LED Strips.

• LED light strips
• Double-sided tape or silicone adhesive
• Zip ties
• Utility knife
• 18-gauge sheathed wire
• Pinch-type wire splitter
• Wire-stripping tool
• Socket or crescent wrench set
• Screwdrivers
• Soldering iron and solder
• Electrical tape
• Electrician's fish wire (interior installation)
• 12 V voltage tester

Most of the people have a nature to avoid risk and seek safety. That is the reason why they would go with a familiar auto parts brand than a new one. It would prove to be safe and they know what to expect. Have a look at our top brands for LED Strips which would offer safety and at the same time decrease the risk of disappointment.

There might be a big-picture overview of LED Strips in your mind, and now it’s time to look at its related components.

• LED Dayliner
• Headlight Strip

Do you want to change your LED Strips on your own? Then have a look at the steps of changing the LED Strips below:

There are some custom cars which would sometimes include custom accent lighting final touch to highlight the lines of the grill or the headlights or sometimes even to illuminate the foot wells which are inside the automobile. It is the flat LED strips which would fit very easily between trim panels and would be adapted very easily for a lot of lighting solutions. The best part is that you can easily cut the flat LED lighting strips to the length which is desired by you for any sort of project and then it should be connected to the existing wiring of the vehicle. If you will connect the LED wiring to a lot of auto light circuits, then you can easily control the illumination of the lights.

Step 1

The LED strip lights should first of all be cut to the sired length by cutting between groups of lights, as per the manufacturer's recommendations.

Step 2

Then the next step would be to expose and then strip the ends of the wires which would lead to the LED lights.

Step 3

The wiring circuit which would be tapped into to power the lights should then be identified. Then circuit which would be used by you would then be able to determine which the lights would be on. Let us understand this with the help of an example. You might install the LED lights which would blink with the turn signal.

Step 4

The voltage tester should then be used so that the right wire can be identified. For example, first of all you should carefully disconnect the wiring harness for the turn signal, then the signal should be turned on and then the wiring harness should be probed to identify the wire which is carrying the current.

Step 5

You should then identify the fuse for the wiring circuit you plan to tap into, and then the fuse should be removed. You should then tap into the wiring circuit, by utilizing a pinch-type splitter to connect a length of wire to connect to the LED lights. Then all you have to do is to insert the wire ends into the splitter and then pinch closed. The splitter and wire bundle should then be wrapped with electrical tape.

Step 6

Then you should route the wiring to the location where you will install the LED lights, by utilizing electrician's fish wire to pull wire which would be beneath carpets. The wiring should then be glued in the place trim panels as per the requirements. The end of the power wire should then be stripped and then you should solder it to one wire on the LED strip light. The soldered wires should then be covered with electrical tape.

Step 7

Both the ends of a length of wire should then be stripped long enough to reach from the LED lights to a bolt or screw on the frame of the automobile. The bolt should then be loosened up and then one end of the wire should be connected to it. The other end of the wire should then be routed to the LED lights and solder it to the LED ground wire. The soldered wires should then be covered with electrical tape. The LED lighting strips should then be mounted in place securely with silicone adhesive or zip ties.