P2782 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P2782 can be described as Downshift Switch Circuit Intermittent/Erratic. The trouble code P2782 can be elucidated as downshift Switch Circuit Issue. P2782 means there is some fault with a circuit for the downshift switch, which is generally because of a disabled manual shifter. This error code would indicate an issue in the electrical circuit of the downshift switch to the transmission range correlation circuit. The switch, wiring, connectors, and mode actuator are included in the circuit and it is used in automobiles which have manually shifting automatic transmissions.

When the PCM (Powertrain Control Module) detects a high voltage in the downshift switch circuit for the tap shifting automatic transmission vehicle, OBD code P2782 gets stored and the check engine light may flash on the dashboard along with disabled tapping shifts.

What causes this problem with the Downshift Switch Circuit Intermittent/Erratic?

• There can be distorted downshift switch
• Downshift switch harness is open or small
• Downshift switch circuit might have inadequate electrical connection

1. Electronic Control Unit - ECU monitors the temperature differences in the boost converter with the help of the temperature sensors to prevent the converter from overheating and malfunctioning. Thus, replace faulty ECU immediately.
2. Engine Control Module - ECM failures and faults can be very difficult to find and resolve as these are very rare and might require a complete reprogramming of the system to avoid wrong codes from getting stored in the system, leading to misdiagnosis. Replace it now!
3. Transmission Control Module - The TCM monitor the transmission system of the vehicle and if it becomes faulty, the vehicle will have transmission performance issue. Thus, replace and reprogram it now!
4. Automatic Transmission Switch - A failed transmission downshifter switch will lead to disabled tap shifting and affected transmission system. Thus, replace the defective switch and replace it immediately.
5. Shift Lever - If the shift lever has failed, the driver will be unable to shift between gears, causing transmission failures and serious damage to various mechanical components leading to hefty repair costs. Thus, replace the faulty shift lever in time.
6. Powertrain Control Module - Faulty PCM can disrupt the normal functioning of the vehicle by affecting the transmission system and the fuel delivery system. This will cause the system to store wrong OBD error and thus can lead to misdiagnosis.
7. Diagnostic Tool - In order to be that DIY guy, you need few diagnostic tools to get your car problems pointed out easily. Our diagnostic tools collection will come in handy to do so, so why not have a look?

We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P2782. They are mentioned here as follows:

Common Symptoms

• Check engine light can start flashing up
• The manual shifter function will be defused
• Transmission will not shift correctly

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P2782:

• Make sure to mend the faulty downshift switch
• It is essential to restore the flawed switches
• Repair or replace the quirky downshift switch harness
• Carefully adjust the faults in the wiring
• Recondition the non-functioning downshift switch circuit
• Adjust the flawed PCM

Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide the best quality of automatic transmissions, PCM, actuator, powertrain control module, body control module, BCM, shift lever, pcm car, ecm car, pcm module, ecm module at marketable prices.

Do you wish to diagnose P2782 error code easily? Here are some steps which you should follow in order to diagnose this fault code:

• You should execute a visual inspection of all wiring, connectors, and constituents related with the upshift/downshift switch circuit.
• Now if everything turns out in good condition, then you should attach the scanner to the diagnostic connector and all freeze frame data and stored trouble codes should be downloaded as it would be very helpful further diagnosis.
• The next step is to clear the code and see if it returns upon testing the system.
• If the code returns check the reference voltage and ground signal of the upshift switch and actuator.
• If either is open, then all the related control modules should be disconnected before the continuity is being tested as well as resistance of all circuits. Disconnect the modules as it would be helpful in preventing the damage from a misplaced investigation when the circuits are being checked.
• The manufacturer's wiring diagram should also be used by a mechanic to test all related circuits using the volt/ohmmeter and then compare their findings to the manufacturer's specifications.
• After that, the code should be cleared up and the entire system should be tested once again, by utilizing a scanner to manually activate the upshift switch.
• Now if the code is returning once again, then you should disconnect and test the powertrain control module for the default.
• The mechanic can also inspect the normal/performance switch if the transmission mode selector fails to operate manually.
• Then you should clear the code once more and test the system to see if the trouble code is returning back again or not.

Common Mistakes When Diagnosing The P2782 Code

• The body control module might start failing
• Non observance of the shift lever assembly
• Some issues with the car wiring