P2780 - OBD Trouble Code

<<See All OBD Codes

The trouble code P2780 can be explained as Downshift Switch Circuit Low. OBD code P2780 gets stored in the powertrain control module (PCM) if the downshift switch performance is out of range or specification. This can cause erratic downshifts and delayed transmission responses.

If the engine control module would detect a variation in the voltage coming from the downshift switch circuit that is outside the parameters set by the automobile manufacturer, then it would store the P2780 error code. This would also give rise to the illumination of the check engine light.

What causes this problem with the Downshift Switch Circuit Low?

• The electrical wiring might be corroded
• Some liquid might be spilled on the upshift/downshift switch
• The electrical wiring might be shorted
• Malfunctioning wiring

1. Engine Control Module - Dead cells in batteries can cause a failure in the engine control module. Many times, a battery is left in the rig long after a cell has died. This would affect the grounding in the car battery.
2. Automatic Transmission Switch - Faulty transmission switch can cause downshifting problems and thus will lead to erratic gear shifts and stalling. Thus, replace it now!
3. Shift Lever - Faulty shift lever will cause delayed transmission shifts and gear slippage. In extreme cases the gear may not shift at all. Thus, replace faulty shift lever now!
4. Engine Control Module - If there is any corrosion or breaks in the internal wiring of the harness, then it can cause a short in the ECM or can also cause corrosion in the ECM through the wiring harness. You can always rely on us as we have the best auto parts for our customers.
5. Powertrain Control Module - The onboard computer, or powertrain control module is the brain of the engine control system. Now if the brain is not working properly, then neither is the car engine. Get it replaced before the situation gets worse.
6. Electronic Control Unit - Is your car jump starting on reverse polarity? Or are you facing some intermittent starting issues? If yes, then it indicates that your electronic control unit is bad. So, it is very important to replace the defective electronic control unit with us at equitable prices.
7. Diagnostic Tools - Buy quality diagnostic tools to check and diagnose OBD code P2780 error with the help of experienced mechanic. Visit us today!

There could be countless symptoms that would accompany this fault code. Willing to know some common symptoms of OBD Trouble Code P2780? Your wish is our demand. Have a look at them below:

Common Symptoms

• Check engine light might come into signal
• The manual shifter function might be damaged
• The transmission might not shift properly

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Make sure to mend the faulty switches
• It is essential to restore the flawed PCM
• Repair or replace the quirky wiring
• Rehabilitate the defaults in the downshift switch
• Carefully adjust the faults in the downshift switch harness
• It is necessary to perform proper service of the unsound downshift switch circuit

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of automatic transmissions, PCM, actuator, powertrain control module, body control module, BCM, shift lever, pcm car, ecm car, pcm module, ecm module and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P2780 code to be stored:

The P2780 error code can be diagnosed by utilizing an OBD-II trouble code scanner. A scanner should be used by a professional technician to notice the freeze frame data, to assemble details about the code. The mechanic can also check to see if there is presence of additional trouble codes. Now if there are a number of codes, then they should be addressed in the same order in which they are appearing on the scanner. After that the mechanic should reset the trouble codes, restart the vehicle, and check to see if the code remains detected. If it does not, then the code was likely triggered incorrectly, or represents an intermittent issue.

Now if you find out that the P2780 error code remains detected, then the technician should undergo a visual inspection of the electrical components in the automatic transmission. You should restore any open or shorted wires, or defective or corroded connectors. Then examine the upshift switch and you can always replace it if it is faulty.

If you are still not able to find the issue, then you should inspect the reference voltage and ground signals, and a digital volt/ohmmeter can be utilized to test for resistance and continuity between all the circuits.

Once any constituent is being replaced, then the trouble codes should be retested by the technician. Then restart the vehicle, and once again inspect to see if the codes return. This is done so that the mechanic would be able to find out that the issue has been solved.

Common Mistakes When Diagnosing The P2780 Code

• Malfunctioning body control module
• There can be a failure in the shift lever assembly
• Wiring problems