Error Code P2765: What It Means & What To Do?

<<See All OBD Codes

Error Code P2765 is defined as Input/Turbine Speed Sensor “B” Circuit Malfunction. This means the transmission is unable to read the RPM of the engine, keeping it from shifting properly and causing erratic and hard transmission.

Error Code P2765 relates to the communication between the PCM (powertrain control module) of the vehicle and the TCM or automatic transmission control module. And if the input sensor doesn’t receive signal that is within the specified parameters set by the manufacturer, the transmission will not be able to read the RPM of the engine, causing the Error Code P2765 to appear.

What causes this problem with the Input/Turbine Speed Sensor "B" Circuit?

• Defective transmission speed sensor
• Defective or faulty speed sensor wiring
• Defective shift solenoids
• Defective speed sensor electrical connection
• Damaged transmission valve body
• Dirty transmission fluid
• Low transmission fluid

1. Engine Control Module - It is not always the components, but the ECM that can also be faulty. It can cause misinterpretation of correct data thus leading to wrong operational decisions which will affect the transmission and overall engine performance. Thus, replace faulty module and reprogram it now!
2. Powertrain Control Module - Powertrain Control Module can also be faulty in rare cases and thus needs through checks for system and software errors. Thus, check and replace it, if required.
3. Electronic Control Unit - The ECU manages the cooling system to control the battery operating temperatures and thus must be replaced if found faulty. Thus, buy new ECU modules and components from us!
4. Diagnostic Tool - Make use of quality diagnostic tools to resolve any OBD error code. Buy quality diagnostic tools from us!
5. Automatic Transmission Solenoid - A lot of shifting problems can be attributed to a malfunctioning shift solenoid since they are responsible for regulating fluid pressure. A transmission that receives too much fluid pressure will have rough shifting, while not enough can cause clutch plates to overheat.
6. Transmission Control Module - The car has to shift through various gears with the precise timing in order to speed up, and the module is the component that is mainly responsible for this operation. An acceleration delay means that it has gone bad and needs fixing.
7. Automatic Transmission Sensor - Without a valid speed signal from these sensors, the PCM will not be able to correctly control the shifting of gears within the transmission. This may cause the transmission to shift roughly or more quickly than normal.
8. Auto Transmission Torque Converter - Overheating is probably the most common sign of torque converter problems, as a drop-in fluid pressure will cause the transmission to overheat. Thus, replace it now!
9. Automatic Transmission Connector - Faulty transmission connector terminals can cause the sensor and solenoid circuits to fail thus, sending wrong info to the TCM. Replace them now!
10. Transmission Fluid - Transmission fluid is no less than the lifeblood of the transmission system. It keeps all the components in the system, allowing them to run smoothly. Its absence can cause the parts to wear and tear beyond repair. The damage will be even worse in an automatic car because the automatic transmission fluid (ATF) doubles as an antifreeze to prevent the engine overheating.

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P2765 here:

Common Symptoms

• Erratic or harsh transmission shift points
• Increased fuel consumption
• Transmission fails to shift
• Fluctuation in speedometer (odometer)
• Lack of speedometer operation
• Engine may stall when coming to a stop

Here are some ways with the help of which you will be able to correct the OBD Code P2765

• Replace any damaged or corroded wiring and connectors
• Flush and fill transmission fluid
• Replace defective input speed sensor circuits and connectors
• Replace defective output speed sensor circuits and connectors
• Replace defective shift solenoid
• Replace defective engine temperature sensor
• Replace any defective system circuits, components, and wiring

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade Ecm, PCM, Transmission Control Module, Output Speed Sensor, Shift Solenoid, Engine Temperature Sensor, Valve Body, Transmission Fluid, Crankshaft Position Sensor and a lot more for our precious customers.

Here are some steps which you should follow in order to diagnose this fault code:

First off, conduct a visual inspection of the input speed sensor. This is to determine the condition of the wiring. Any damages must be repaired or replaced as needed.

Then, test the voltage and ground wiring to the sensor to see if there are wiring failure or problem in the sensor itself. If the wiring checks out, the mechanic will replace the sensor, reset the PCM and then take the vehicle for a test drive.

If the problem persists, then the issue may be with the automatic transmission itself.

Common Mistakes When Diagnosing the P2765 Code

Some of the common mistakes done while changing diagnosing the OBD code P2765 are:

• Engine Misfire problem
• Internal Transmission problem
• Driveline problem
• Input speed sensor issue
• Crankshaft position sensor issue