Guide To P2727 OBD Error Code Solutions
OBD Code P2727 - Pressure Control Solenoid "E" Control Circuit/Open
Do
you know the probable causes and symptoms of P2727 error code? Do you know how
to fix them? The transmission which fails to shift as needed is known as
pressure control solenoid "e" control circuit/open. In order to
control the hydraulic pressure, pressure control solenoids are used by the
transmission control module. It provides various gear ratios which are highly
essential to apply clutch packs in the transmission so you can properly boost
your vehicle down the road. If the pressure control solenoid is not performing
well, and if it is identified by the TCM, then the error code will be set.
Learn More About OBD Error Code P2727
This
general transmission trouble code is applicable to OBD - II vehicle with
automatic transmission. This is
restricted to vehicles like Ford, GMC, Chevrolet, Honda, BMW, Saturn, Land
Rover, Acura, Nissan, Saturn, etc. The repair process will vary based on the
make, model and year of configuration though it is very generic. When the P2727
error is found, it means the PCM has identified an issue with the transmission
pressure control solenoid "E" control circuit. The specific issue is
set depending on the specific error that is identified by the PCM. An automatic
transmission operates the bands and clutches so that it can make changes to the
gears by correctly fixing the fluid pressure at the right place and time. The
work of the transmission control solenoid is to correct fluid pressure so that
the automatic transmission will function correctly and shift smoothly. The
pressure is monitored by the PCM within the solenoid and it routes the fluid to
several hydraulic circuits to change the transmission gear ratio correctly as
required.
What
causes this problem with the Pressure Control Solenoid "E" Control
Circuit/Open?
- The
line pressure solenoid valve 'E' might seem to be defective.
- You
might find an opening in the line pressure solenoid valve 'E’ harness or the
circuit might be shorted.
- The
electrical connection might be poor in the line pressure solenoid valve 'E'.
- Reduced transmission fluid.
- Polluted
transmission fluid.
Replace/Repair These Parts To Fix OBD Code P2727
- Powertrain Control Module - Powertrain control module will
monitor and compensate for any change in altitude and looks after the overall
health of your car. The right replacement for your faulty powertrain control
module can be found at Parts Avatar
at best prices.
- Pressure Control
Solenoid - Replace
the damaged pressure control solenoid from PartsAvatar to avoid P2727 error.
- Transmission Control Module - Do you find trouble while shifting
to high gears? Then you have to quickly replace the faulty transmission control
module to avoid the P2727 error.
- Automatic Transmission Fluid - The automatic transmission fluid
must be replaced for every 30,000 to 60,000 miles. Check the automatic
transmission fluid if it is dirty. If you find them dirty, replace them
immediately so that the engine can function normally.
- Engine Wiring Connector - Do you find any cuts or leaky areas?
Then it’s high time to replace the engine wiring connectors as they cause
malfunctioning of the vehicle.
- Filters - Check the filter for damages or any debris. If it’s damaged, get the right replacement from Parts Avatar.
- Fuel Pump - The engine will not start at all or it will start to surge as
you accelerate. This is one of the common symptoms for a faulty fuel pump which
needs quick replacement so that the engine functions normally.
Symptoms Of OBD Error Code P2727
If
you are facing OBD error code P2727, then there are significant common symptoms
that can be felt or observed. We have worked out a list here to help you out in
understanding this problem better.
Common Symptoms
- Fuel consumption will be more.
- Improper
shift by transmission.
How To Correct P2727 Pressure Control Solenoid "E" Control Circuit/Open
It
is very important to fix the fault code P2727. So here are some ways with which
you can correct this issue:
- Fluid
and filter must be altered.
- Damaged
pressure control solenoid has to be fixed.
- Faulty
transmission valve body should be fixed.
- Broken
transmission pump need rework.
- Flush
the transmission to clear blockages.
- Corroded
connectors have to be cleaned.
- Changing
cables.
- PCM has to be changed.
To do all this, you will need a few high-quality auto parts such as transmission, PCM, pressure control solenoid, transmission control module, fluid, filter, pump, wiring, connector, valve and so on. From where will you get them? From your local store? Well, why go there when you can order quality parts with us while sitting in the comfort of your home. So, just browse through our website and order your needed parts today.
Easy Diagnosis Of Engine Error OBD Code P2727
It
is essential to diagnose this fault code. Here are some steps which a mechanic
should follow for diagnosing the problem that triggered a P2727 code to be
stored:
Fluid & Wiring Inspections
- First
and foremost check for the apt level of fluid in your vehicle as well as their
conditions.
- If
you don’t remember when you previously fixed the fluids or filter, you can
always check the records.
- Secondly
check the connectors and its related connections, connections to the PCM,
transmission pump and solenoid.
- The transmission pump will be driven either mechanically or electrically based on this configuration.
Advanced
Steps
- Each
vehicle has its own specific and advanced procedure and so you’ll need a proper
tool to diagnose them. Start processing with the help of a digital multimeter
and correct technical reference of your vehicle.
- Voltage
requirement will change for every vehicle and so it is wise to use a particular
troubleshooting chart for your vehicle.
- Based on the configuration and design of the transmission, the need for fluid pressure will vary.
Continuity
Checks
- It
is always best to turn off the power of your vehicle and check for continuity.
Set the readings of the connections to 0 ohms or as specified by the
manufacturer.
- If you don’t find any resistance or continuity, then it is a clear sign that the wires are broken or there is opening or shorted circuit which needs immediately fixation.
Common
Mistakes When Diagnosing the P2727 Code
- Unsuccessful
transmission control module.
- Reduced
level of fluid in the transmission.
- Faulty transmission shift solenoid.
- Wires
face difficulties.