Error Code P2717: What It Means & What To Do?

<<See All OBD Codes

If you are experiencing unusual response of the throttle, lack of power form the car engine, impact on the fuel economy, engine stalling and harsh shifts and frequent illumination of the Check Engine Light, it might be an indication of the OBD Code P2717 error.

When the code P2717 appears in your powertrain control module (PCM), it means that the PCM is not reading the correct electrical voltage drops from the Pressure Control Solenoid as it does its job. It may also be that the PCM reads the correct electrical readings but that the Pressure Control Solenoid has malfunctioned.

What causes this problem with the Pressure Control Solenoid "D" Intermittent?

• Dirty, contaminated, or degraded transmission fluid
• Low transmission fluid level
• Mechanical failure of transmission components
• Internal pressure losses
• Clogged fluid passages
• Malfunctioned pressure control solenoid
• Transmission speed sensor faulty
• Transmission torque converter issues

1. Electronic Control Unit - ECU monitors the temperature differences in the boost converter with the help of the temperature sensors to prevent the converter from overheating and malfunctioning. Thus, replace faulty ECU immediately.
2. Automatic Transmission Module - Sometimes the automatic transmission module is unable to communicate or correctly anticipate the speed of the vehicle and thus creates difficulty in gear shift leading to sluggish acceleration, throttle response and stalling. Thus can also hamper a lot of components physically and thus must be checked and replaced, if required.
3. Engine Control Module - ECM failures and faults can be very difficult to find and resolve as these are very rare and might require a complete reprogramming of the system to avoid wrong codes from getting stored in the system, leading to misdiagnosis. Replace it now!
4. Powertrain Control Module - Faulty PCM can disrupt the normal functioning of the vehicle by affecting the transmission system and the fuel delivery system. This will cause the system to store wrong OBD error and thus can lead to misdiagnosis.
5. Diagnostic Tool - In order to be that DIY guy, you need few diagnostic tools to get your car problems pointed out easily. Our diagnostic tools collection will come handy to do so, so why not have a look?
6. Automatic Transmission Solenoid - A functioning transmission automatically downshifts as it slows down and changes to first gear once you reach a complete stop. However, a bad shift solenoid will cause your transmission to downshift uncontrollably or not at all.
7. Automatic Transmission Sensor - If you notice that your transmission is shifting harshly or roughly, you should contact a local certified mechanic as soon as possible and get the transmission sensor tested. Replace faulty sensor now!
8. Auto Transmission Torque Converter - If you start to feel shudders when driving, this could mean that you have torque converter problems on your hand. It will often feel like running over rough road or bumps and you will definitely notice it when it happens.
9. Automatic Transmission Connector - Damaged connectors will affect the functionality of pressure control solenoid and thus must be replaced as quickly as possible.
10. Transmission Fluid - Erratic shifts cause the shifting of gear to happen too late or too soon along with banging sound. This can be due to faulty transmission fluid. Thus, refill the transmission fluid now!

If you are facing OBD error code P2717, then there are significant common symptoms that can be felt or observed. We have worked out a list here to help you out in understanding this problem better.

Common Symptoms

• Stored trouble code and an illuminated warning light
• Reverse gear engagement delayed, or may not engage at all
• Transmission slippage
• Erratic gear shifts and delayed response
• Affected fuel economy
• Malfunction indicator light on

It is very important to fix the fault code P2717. So here are some ways with which you can correct this issue:

• Transmission fluid replacement
• Transmission range switch replacement
• Repairing an open or short in the wiring harness or replacing it
• Park/neutral position switch repair or replacement
• Replace transmission pressure control solenoid
• Broken electrical connections repair or replace

However, if you face any issue then we have stocked a wide range of best priced Transmission, PCM, Pressure Control Solenoid, Transmission Fluid, Transmission Control Module, Electronic Pressure Control Solenoid, Pressure Gauge, Connector, Shift Solenoids, Electronic Pressure Regulator, Torque Converter, High Pressure Pump, Transmission Filter, Transmission Valve Body, Transmission Pump, Transmission shift solenoid, Driveline and more to help you out in fixing your car.

If you want to easily diagnose this fault code P2717, then all you have to do is to follow the steps which are mentioned below:

• The P2717 code should be diagnosed with an OBD-II trouble code scanner. A trained technician will look at the freeze frame data on the scanner to assess the code, and to check for the presence of any other trouble codes.
• The mechanic will begin by visually inspecting the electrical components in the transmission circuit. Any wires that are shorted, connectors that are open or corroded, or fuses that are blown will need to be replaced.
• Check the dipstick to make sure that the transmission fluid is not low and refill if required. Look at the fluid to determine if it is clean and replace, if needed.
• Smell the fluid to determine if there is a burnt odour. If the fluid smells burnt, remove the transmission pan to check for debris. Also check for burnt wiring and faulty circuitry.
• Inspect the transmission to determine if damage has occurred that will require extensive repairs. Perform a pressure control solenoid continuity test to check for open or short in the circuit.
• Check for Transmission Control Module and Powertrain Control Module faults that may require repairs, reprogramming or replacement. Although, it is rare but still must not be rules out.

Common Mistakes When Diagnosing the P2717 Code

It is important to follow the diagnostic steps properly to correct the OBD code P2717 error. Following are the problems that can be missed and are mostly the reason for this kind of problem:

• Internal transmission failure
• Powertrain Control Module (PCM) failure
• Transmission Control Module (TCM) failure
• Transmission valve body failure
• Wiring issue and connector problems
• Automatic transmission solenoid faulty