P2714 OBD Error Code: Problem & Solutions

<<See All OBD Codes

Is your Check Engine Light illuminated on the car’s dashboard? Are you experiencing sudden drop in the fuel economy with stalling of the engine? Or is there any engine stalling and gear slipping? Then, there might be a possibility of an issue with the transmission pressure control of the car thus indicating OBD Code P2714 error.

The transmission pressure control solenoid controls the fluid pressure to the internal friction plate clutches or drum bands. A bad or failing transmission pressure control solenoid can cause slipping, which can result in the transmission overheating. If left unrepaired, the slipping will ruin (burn or fry) the friction clutches and bands causing transmission failure. Thus, when the transmission control module detects that the pressure control solenoid “D” has malfunctioned, OBD code P2714 gets stored in the system.

What causes this problem with the Pressure Control Solenoid 'D' Performance/Stuck Off?

• Low or dirty transmission fluid level
• Transmission oil leak
• Pressure control solenoid malfunctioning
• Transmission clutch problems
• Low oil pressure
• Transmission control module failure
• Transmission speed sensor failure
• PCM failure
• Corroded connections or pins
• Wring issue (corrosion, chafed,melted)

1. Engine Control Module - The solenoid might cause a short in the engine control module because of corrosion in the solenoid or the wire running from the solenoid to the ECM harness.
2. Powertrain Control Module - A trouble with the PCM would mean that it is unable to determine the right fuel mixture and would send the car engine either more or less fuel than it requires. Now when the engine gets more, the carbon emission would increase and fuel economy would drop. In case of the opposite, the engine will choke, stutter, and might start stalling sometimes.
3. Diagnostic Tool – Usually any OBD code problem requires deep insight into the problem and high grade tools in order to fix it properly. Thus, buy quality diagnostic tools form us!
4. Engine Control Module - Dead cells in batteries can cause a failure in the engine control module. Many times a battery is left in the rig long after a cell has died. This would affect the grounding in the car battery.
5. Automatic Transmission Solenoid – The transmission solenoid is responsible for managing the hydraulic pressure in transmission shaft for managing proper gear shifts. Thus, replace faulty solenoid now!
6. Transmission Control Module – If the TCM is unable to detect the output shaft speed, it won’t be able to manage correct gear ratios and the transmission may slip. Thus, replace it now!
7. Automatic Transmission Sensor – Faulty transmission sensor may lead to engine stalling and transmission slippage. It can cause erratic gear shift and increased transmission pressure and temperatures. Thus, replace it now!
8. Auto Transmission Torque Converter – The torque converter is the part of your car that handles how much fluid is passed on to the automatic transmission and keeps the engine running even at complete stop. Thus, replace the faulty torque converter immediately.
9. Automatic Transmission Connector – Check for damaged connector terminals and breakages and replace the faulty connectors immediately. Buy new transmission connector now!
10. Transmission Fluid – Always keep in check for the transmission fluid as without it, the transmission may overheat and cause mechanical failures. Thus, keep the transmission fluids in check.

Willing to know some common symptoms of OBD Code P2714? Your wish is our demand. Have a look at them below:

Common Symptoms

• Intermittent condition
• Check engine light illumination
• Lack of engine power and misfires
• Slow speeds
• Increased fuel economy
• Transmission slipping
• Transmission shifts erratic
• Harsh gear shifts

We have listed out some ways which would help you to correct the occurrence of OBD Code P2714. They are mentioned here as follows:

• Shift solenoid replacement
• Faulty wiring and connector replacement
• Powertrain control module replacement
• Transmission control module replacement
• Replace the transmission fluid and filter
• Overhauling the current transmission
• Installing a brand new transmission

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior varietyof Transmission, PCM, Pressure Control Solenoid, Transmission Fluid,Transmission Control Module, Electronic Pressure Control Solenoid, Pressure Gauge, Connector, Shift Solenoids, Electronic Pressure Regulator, Torque Converter, High Pressure Pump, Transmission Filter, Transmission Valve Body, Transmission Pump, Transmission shift solenoid, Driveline and many more. Now all your problems would vanish within no time.

If you want to easily diagnose this fault code P2714, then all you have to do is to follow the steps which are mentioned below:

• You will need a digital volt ohm meter (DVOM) for the complete test. Also make use of a basic OBD code scanner to reset the computer and erase the code.
• Begin by checking the levels of the transmission oil. Visually inspect the transmission itself for damage. Inspect the vehicle housing for signs of cracks or damage. If there are any cracks that may or may not be leaking, the transmission should be replaced. Replace any damaged seals. Look for the speed sensors on the transmission and inspect sensors and connectors for signs of damage. If any damage present, repair or replace.
• Inspect for optimal oil pressure. Using an oil pressure gauge, test the transmission oil pressure. Make use of the transmission pressure test port. Connect gauge to the test port and start vehicle and ensure there are no leaks at connection.
• Check for faults in the pressure control solenoid. Unplug the transmission solenoid. Using multimeter, you will need to test resistance values within the solenoid. If values aren’t within specifications, replace the solenoid and clear codes.
• Identify wires involved in solenoid circuits. Using multimeter check for continuity, shorts and open in the wires involved. Also make sure that battery is disconnected before testing and it will also include the ECM. Repair any problems in the circuit and clear codes.
• Test the TCM by back probing the connector and measuring electrical values to ensure it is functioning as it should.

Common Mistakes When Diagnosing The P2714 Code

When diagnosing a P2714 code the most common misdiagnosis would be to have the transmission replaced assuming that internal damage has occurred. It is important to note that the transmission is faulty before replacing it. It is best to make sure the transmission actually needs to be replaced before adding even more to the cost of repairs.