P269D - OBD Trouble Code

<<See All OBD Codes

Is the diesel exhaust fluid faulty? Are you looking for the diagnostic steps for P20B1 error code? Then keep reading further as you are at the right place. A decrease in engine performance is usually known as exhaust aftertreatment glow plug control circuit low. The conversion of the remaining exhaust particles into harmless gases is carefully assisted by the diesel exhaust fluid (DEF). The temperature of the exhaust system has to be more so that the leftover exhaust particles can be easily burnt off.

In order to bring the diesel particulate filter up to the expected temperature, the DEF fluid has to be injected into the exhaust stream. This will finally help in the conversion of harmful NOx into nitrogen, water, and carbon dioxide. In extremely cold temperatures, the glow plugs keep the DEF from freezing. If the glow plug does not function as expected, the P269D error will get stored.

The PCM will looks after the exhaust aftertreatment glow plug control circuit. If the factory expectation is not correctly met by the exhaust aftertreatment glow plug control circuit, then the PCM sets the P269D error code in the vehicle.

What causes this problem with the Exhaust Aftertreatment Glow Plug Control Circuit Low?

• Broken exhaust aftertreatment glow plug.
• The harness of the exhaust aftertreatment glow plug might be shorted or it might have an opening.
• The electrical connection of the exhaust aftertreatment glow plug might be bad.

1. Powertrain Control Module – The engine will fail to start or the fuel economy will be poor if the powertrain control module is faulty. Get them replaced as soon as possible so that you can get rid of the P2620 error code
2. Glow Plug - Weak engine performance is a sign of a damaged glow plug. Get a new glow plug from PartsAvatar to avoid the P269D error.
3. Shift Solenoid – The shift solenoids can turn out to be bad if there is any opening in the circuit system. Visually inspect them and repair it as quickly as possible.
4. Electronic Pressure Regulator – Poor engine performance is an indication of the faulty electronic pressure regulator. Fix it quickly.
5. Glow Plug Relay – If the relay is not connected properly there can be an opening or shorted circuit. Visually inspect the component and repair them.
6. Engine Control Module – You can easily find out that the engine control module in your vehicle is damaged if your vehicle faces issues like stalling or misfiring. Additionally, the behavior of the engine can be erratic. In one such scenario, it is always best to replace the faulty engine control module

We at Parts Avatar Canada care for our customers, and that’s why we will help you to diagnose P269D code by listing out some major symptoms. They are mentioned below as follows:

Common Symptoms

• Weak performance by the engine.
• Regeneration by the DPF will be impossible or it might not take place.
• Illumination of the check engine light.

Learn the ways with which you can correct this trouble code:

• Firstly you must change the faulty glow plugs.
• Look for damages in the glow plug relay and replace them.
• Any defects in the PCM/ECM must be fixed.

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high-grade PCM, glow plug, shift solenoid, electronic pressure regulator, glow plug control module, glow plug relay, ECM and a lot more for our precious customers.

Here are some steps which you should follow in order to diagnose this fault code:

• To accurately diagnose P269D code you will need a diagnostic scanner, a reliable source of vehicle information, and a digital volt/ohmmeter (DVOM).
• Find an exact TSB that matches your engine make and model and locate it to find the shown symptoms and stored codes.
• You will need diagnostic flowcharts, wire diagrams, connector face views, connector pinout charts, component locations, and component testing procedure from the vehicle information source.
• This info can help you to correctly diagnose P269D code.
• Once you inspect all the glow plugs and its control wires, connectors, connect the diagnostic scanner to the diagnostic port of the vehicle.
• Recover all the stored codes and freeze the frame data.
• Test drive your car to see if the code is reset. Proceed driving either if the PCM enters readiness mode or continue with a diagnosis if the code is reset.
• If not so, there is an irregular connection and you have to worsen the condition.
• The best way to test the glow plug is to remove them and apply battery voltage.
• As per the manufacturer’s suggestion, test the fuse and relays with the circuit loaded.
• The unloaded circuit of a fuse will be functioning normally and lead you to the wrong path.
• If both the fuse and relay functional normally, use DVOM to test output voltage.
• If you detect the voltage at the glow plug timer, PCM then there can be an open circuit. Simply replace them.
• A P269D code cannot be caused by a bad glow plug as it is related to control circuit code.
• A bad glow plug can cause an error code.
• One of the common issues is diagnosing the wrong cylinder.
• Before you start diagnosing make sure you diagnose the right cylinder.

Common Mistakes When Diagnosing the P269D Code

• Glow plug control module might be damaged.
• Glow plug relay might be defective.
• Malfunctioning of the powertrain control module.
• Broken wires can cause some issue