Error Code P269A: What It Means & What To Do?

<<See All OBD Codes

Do you know what does exhaust aftertreatment glow fuel injector ‘A’ circuit mean? Are you looking for the diagnostic procedures? Then keep reading further. The reduced engine performance is usually known as exhaust aftertreatment fuel injector "A" circuit high. The exhaust particles which are left behind is converted into harmless gases which are assisted by the DEF. the temperature must be high to burn these exhaust particles. As the DEF is injected in the exhaust stream, DPF will be raised to the expected temperature. This will finally convert the injurious NOx to nitrogen, CO2, and water. The DEF gets injected into the DPF by the DEF injector. The P2699A error will get stored, if the injector does not function as commanded.

The exhaust fuel addition injector assembly is usually placed on the outlet of the turbocharger sub-assembly, and low-pressure fuel is sent to the exhaust fuel addition injector assembly in the supply pump assembly by the feed pump. The fuel gets added to the exhaust fuel addition injector assembly from the engine control module by the control signal. For 2 different controls, this injector is used, forced regeneration and PM reduction.

What causes this problem with the Exhaust Aftertreatment Fuel Injector "A" Circuit High?

• The exhaust aftertreatment glow plug might be defective.
• There might be an opening in the exhaust aftertreatment glow plug or the circuit might be shorted.
• The electrical connection of the exhaust aftertreatment glow plug circuit might appear to be weak

1. Turbo Charger – The acceleration of the vehicle will be very slow if the turbocharger is faulty. Fix it quickly to avoid the P269A error code.
2. Fuel Injector – Poor idling is a common symptom for a defective fuel injector. Get the replacement for fuel injector from PartsAvatar.
3. Engine Control Module – Engine stalling is one of the symptoms for a defective ECM which needs replacement as soon as possible.
4. Powertrain Control Module – Illumination of the check engine light is a common symptom of faulty PCM. Change it immediately.
5. Diesel Exhaust Fluid – If the diesel exhaust fluid is poor, then the malfunctioning of the machine SCR’s system will take place. Replace it as soon as possible.
6. Exhaust System – If there is a loud roaring noise in the vehicle, then it’s high time to replace the faulty exhaust system and get rid of the P269A error code.
7. Diesel Particulate Filter - Does your engine fail to start? Does your engine find it very hard to start or accelerate? Then the DPF can be faulty. Change it quickly.
8. Oxygen Sensor – The vehicle will function normally if the faulty oxygen sensor which shows poor gas mileage is replaced or fixed immediately.
9. Exhaust Gas Temperature Sensor – Idling or stalling of the engine is a sign of a defective exhaust gas temperature sensor. Avoid the P269A error by replacing the damaged EGT sensor with a new one from PartsAvatar.

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P269A here:

Common Symptoms

• Reduced engine performance.
• Regeneration by the DPF will be impossible.
• Blinking of the engine light as well as the warning light of the service engine

Want to correct the Trouble Code P269A? Read these points mentioned below:

• Replacing the broken or damaged glow plug is the 1^st step.
• Look for possible damages in the glow plug relay and change them.
• PCM/ECM issue is very rare. Replace them if they are found to be malfunctioning.

Apart from this, you might need to replace other damaged parts too like a turbocharger, fuel injector, ECM, diesel particulate filter, exhaust temperature, PCM, exhaust system, oxygen sensor, exhaust gas temperature, electronic pressure regulator and more. You can easily find all these parts with us. Not only that you can get these parts shipped to your door free if your cart value happens to exceed $99.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P269A code to be stored:

• A diagnostic scanner, a reliable source of vehicle information, and DVOM will be needed to diagnose P269A code.
• Find the right TSB that matches with your vehicle make, model as it can help you to identify the stored error codes and perform diagnosis.
• Also, you have to obtain other diagnostic information like diagnostic flowcharts, wiring diagrams, connector face views, component locations, and component testing procedures to diagnose P269A code.
• Visually inspect the glow plug, control wires, glow plug connectors.
• Connect the diagnostic scanner and recover all stored codes and data.
• Test drive to see if the code returns. Either PCM enter readiness mode or code will be reset. If any of these 2 happens, continue diagnosing.
• Else, there will be an irregular connection where you have to worsen the situation before diagnosing.
• The best choice is by removing the glow plugs and applying battery voltage.
• If the plugs work properly, test the battery for voltage with DVOM.
• It’s best to test all the fuses, relays, connected circuits with a loaded circuit.
• The circuit may appear to function normally which leads to the wrong path.
• Use the DVOM to test output voltage if all the fuses and relays function properly. Presence of voltage in the glow timer indicates that there is an opening or short circuit. Replace them as desired.
• A defective glow plug cannot be the only reason for P269A error code in the system. It can also arise due to changes in the control circuit.
• Trying to diagnose the wrong cylinder is one common error.
• Make sure you start diagnosing the right one before proceeding.

Common Mistakes When Diagnosing the P269A Code

• Faulty DEF injector.
• Electrical wires might cause some trouble.
• Broken powertrain control module.