P266B - OBD Trouble Code

<<See All OBD Codes

OBD error code P266B is an OBD-II generic code. Thought its generic, the steps to resolve it might vary a bit depending upon the specific make and model. Your vehicle will flash this OBD error code P266b when it has few troubles with the ‘A’ rocker arm actuator position circuit. If you wish to know more about this error code, you can go through our subsequent sections.

Wondering what this alien word obd P266B actually means? Well, the new generation vehicles make use of this variable valve technology to allow airflow across the engine at higher RPMs. Hence, it allows your vehicle to perform better. OBD error code P266B will be set by your vehicle’s engine control module when it detects signals that are out of factory specifications. To know more about this error code and few of it’s common causes, take a look at the section below.

What causes this problem with the A Rocker Arm Actuator Position Sensor Circuit Range/Performance?

• Inoperative “A” rocker arm actuator sensor
• Use of wrong engine oil or engine oil being low or overfilled
• Poor electrical connections within the “A” rocker arm actuator sensor circuit
• Rocker arm actuator sensor harnesses being open or shorted

1. Engine Control Module - Also abbreviated as ECM is an integral control unit. So a defective one should be changed immediately replaced or reprogrammed to avoid any further damage. If you need one for your car, you can easily find with us for your specific car make and model with us at PartsAvatar and that too at reasonable prices.
2. Powertrain Control Module - Your vehicle’s PCM that is also known as the “brain” of the car should be changed immediately if broken or defective in order to avoid further problems caused due to an Error Code P266B. If you need one for your vehicle, you can easily find one with us.
3. Electronic Control Unit - The ECU is responsible for coordinating the temperature sensor to control the blower fan for keeping the battery temperatures under control. So, replace faulty ECU components now!
4. Diagnostic Tools - In order to be that DIY guy, you need to few diagnostic tools to get your car problems pointed out easily. Our diagnostic tools collection will come in handy to do so, So why not have a look?
5. Rocker Arm - The function of the rocker arms is to assist the pushrods in opening and closing the exhaust valve and intake value. This helps in proper combustion process and adequate power output from the engine. Thus, replace the faulty rocker arm now!

Next important thing you need to know about are the common symptoms for this obd error code P266B with your fuel volume control.

Common Symptoms

• Rise in fuel economy of your vehicle
• Steep fall in engine performance

Learn the ways with which you can correct this trouble code P266B:

• Repair or replace the defective oil pump
• It is essential to restore the flawed oil control valve
• Repair or replace the quirky rocker arm actuator
• Fix the defaults in the oil pressure sensor
• Fix the bad wiring and connectors

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of PCM, Rocker Arm Assembly, Valve Lift Controller Assembly, Rocker Arm Actuator, ECM and a lot more. We are sure that now all your issues would be resolved.

Now, in order to replace the problem it is extremely essential to diagnose it efficiently and appropriately. While doing so you might commit few mistakes, to prevent you from doing so we have listed out few steps for you to keep in mind.

• Start by carefully examining the crankshaft and camshaft positions using electromagnetic sensors.
• Begin a proper diagnosis by making sure that all engine timing indicators are properly aligned. Check the test belt or chain deflection using manufacturer’s specifications.
• Next, test the VVT or VCT solenoids and circuitry if timing components prove to be properly aligned and in good working order.
• Check and replace faulty electrical wiring and connectors as they are more prone to fail than sensors, especially where oil or other corrosive fluids are present.
• Make use of an OBD-II scanner (or code reader), a digital volt/ohmmeter, and an oscilloscope to diagnose this error.
• Repair or replace damaged, disconnected, shorted, or corroded wiring, connectors, and components as necessary. Always retest the system after repairs are completed to ensure success.
• If all system wiring, connectors, and components (Including fuses) appear to be in normal working order, connect the scanner (or code reader) to the diagnostic connector and record all stored codes and freeze frame data. Inspect the PCM for any errors and reprogram it, if necessary.

Common Mistakes When Diagnosing the P266B Code

• When diagnosing the P266B OBD-II trouble code, the most common mistakes made by technicians or that you are most likely to make are:
• Ignoring pcm failure
• Failing variable valve lift controller assembly
• Problematic wiring