Error Code P2653: What It Means & What To Do?

<<See All OBD Codes

Error code P2653 popping? Don’t know where to start from? Don’t worry, Parts Avatar to the rescue! Here’s all you need to know about the error code P2653. This generic OBD-II code decreased engine performance is described as a "B" rocker arm actuator control circuit low. To enable increased air flow through the engine at higher RPMs, modern vehicles use the variable valve technology. This leads to enhanced performance over wider range. Currently, the manufacturer’s can be seen preferring variable valve lift system that permits the valve to open wider.

The powertrain control module controls the operations of the assembly. Also, one can locate the the position sensors inside the variable lift rocker arm assembly. The code P2653 sets as soon as the solenoids present in the assembly fail to function.

What causes this problem with the Rocker Arm Actuator Control Circuit Low Bank 1 ?

• Damaged oil control valve
• Low oil pressure present Low oil levels
• Oil control valve having open circuits
• Defective powertrain control modules (rare case)
• Fault in the electromagnetic sensors (rare case)

1. Rocker Arm - The rocker arm installed performs the chief task of controlling and regulating the air flow and the exhaust. If your is damaged, we recommend you to change or repair it as soon as possible to avoid all these problems and the error code P2653.
2. Oil Control Valve - Check engine light illuminated? Dirty engine oil? All these problems are caused due to a fault in the oil control valve. Visit Parts Avatar today for top notch oil control valves offered at just the right prices.
3. Engine System Parts - Is your car not starting? Hate these erratic halts? Then this is caused likely due to malfunctioning engine system parts. We advise you to get it repaired or replaced immediately if you want to save your hard earned money and time from being wasted.
4. Powertrain Control Module - Now get your error code P2653 solved immediately with your new powertrain control module available at Parts Avatar at the most reasonable prices. Changing one on time can help you get rid of all other problems too that may have been hampering the operation of the vehicle.
5. Rocker Arm Position Sensor - Suddenly observing a flashing check engine light? A defect in this auto part directly affects the functioning of the VVT. So we advise you to get it changed or repaired immediately.
6. Rocker Arm Solenoid - Get your error code P2653 fixed instantly with a new rocker arm solenoid. A jammed one can be the reason behind these unexplained jerks in the vehicle. Parts Avatar right place that provides the best rocker arm solenoids across the country.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P2653 code by mentioning some major symptoms below:

Common Symptoms

• Fall in the engine performance
• Poor fuel economy

Have a look at some ways with which you can correct the P2653 code:

• Make sure that oil levels present are adequate. If not, they should be increased or decreased accordingly
• The oil pressure should be checked too. It is advised to make changes as per the requirements (you can increase it)
• A damaged oil control valve should be repaired or replaced as soon as possible
• Perform amendments to fix the problems present in the oil control valve circuits (loose wires or short circuits)
• Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of rocker arm, oil control valve, engine, powertrain control module, position sensors, solenoid and a lot more. We are sure that now all your issues would be resolved.

Here are some steps which you should follow in order to diagnose this fault code:

• Firstly, make use of a standard OBD-II trouble code scanner to diagnose the code P2653. The mechanic should check the freeze frame data to acquire information about the code and also check for the additional codes stored. Now that freeze frame data has been analysed, the codes should be reset by the mechanic and the vehicle should be test driven. If the error code P2653 fails to return, if would have been detected falsely.
• If in case it does, the oil levels and pressure should be checked by the mechanic. Make sure the engine timing indicators are integrated correctly. If the indicators and oil check out to be in order, the oil control valve and the valve circuit should be inspected. If all seems to be working in order, the electromagnetic sensors and the powertrain control module should be checked.
• Now that all the repairs and replacements have been performed, the error codes should be reset.

Common Mistakes When Diagnosing the P2653 Code

Here we have listed a few common mistakes that should be avoided while diagnosing the error code P2653:

Generally, the most common mistake triggering the error code is failing to adhere to the diagnosis protocol. It is essential to stick to the trouble code diagnosis protocol to avoid mistakes. Failing to do so is likely to cause false replacement of the oil control valve while the problem was only low oil level or pressure levels.