P2652 - OBD Trouble Code

<<See All OBD Codes

See the error code P2652 flashing? Well, all you need is this little guide by Parts Avatar that’ll definitely help you solve the error code. The rocker arm actuator receives orders from the engine control module (ECM) to monitor the oil hydraulic circuit. The variable valve timing system receives oil flowing through the rocker arm actuator to adjust the engine’ valve timing.

The engine performance, fuel economy and the emissions can be enhanced by simply making use of the variable valve timing (VVT) system. Further the engine control module performs the task of monitoring the rocker arm actuator circuit and stored the code P2652 whenever the ‘B’ rocker arm actuator circuit fails to fall out the manufactures provisions.

What causes this problem with the Rocker Arm Actuator System Stuck on Bank 1?

• Excessive or low engine oil
• Wrong type of engine oil
• Malfunctioning ‘B’ rocker arm actuator
• The harness in the ‘B’ rocker arm actuator is loose or burnt
• Weak electrical connection running in the ‘B’ rocker arm actuator

1. Engine Control Module - The engine control module if defective can lead to problems related to rough idle, slow emissions and engine stalling. Change or repair it now if you want to get rid of the error code P2652 and these complications.
2. Rocker Arm - Weary and damaged rocker arm can often be problematic. So to add some spark to your ride you definitely need the perfect quality rocker arm offered at Parts Avatar. Isn’t that just the perfect deal?
3. Engine Valve - Love travelling? But tired of these problems like a difficulty starting the vehicle? We advise you to get your engine valve fixed right away in order to get rid of all these problems.
4. Engine Oil Pressure Sensor - Error code P2652? Don’t know the reason behind it? Well, it could be due to a possible malfunction in the engine oil pressure sensor. We advise you to repair or replace it now. Visit our site today for premium quality products!
5. Powertrain Control Module - A lot of unexplained symptoms are likely to be experienced as soon as the PCM gets damaged. The powertrain control module enables the system and transmission to work in tandem. So a fault in the PCM can affect not only a few parts but the functioning of the entire system. Tune into Parts Avatar for top notch sets of PCM.
6. Engine Wiring Connectors - Misfires? Halts? Then this is likely indicative of failed engine wiring connectors in the system. Visit us today to get your hands on our premium quality products. Log in now!
7. Variable Valve Timing Unit Gasket - The variable valve timing unit gasket controls the air flow along with the exhaust. So do have any idea how damaging it can be for the overall performance of the system? Log in now to get your changed immediately.

Willing to know some common symptoms of OBD code P2652? Your wish is our demand. Have a look at them below:

Common Symptoms

• An illuminated check engine light
• The driver may observe audible tap or tick from the engine
• There are chances of the vehicle entering the limp mode (thereby limiting the speed to under 40 miles per hour)
• Oil pressure sensor failure
• Defective oil pump

We have listed out so ways which would help you to correct the occurrence of OBD code P2652: They are mentioned here as follows:

Firstly, it is essential to fix a faulty oil pump

• It is important to perform a thorough cleansing of the screens on the oil pressure sensor or rocker arm actuator
• The oil and filter if contaminated should be changed right away
• Repair or replace a malfunctioning engine control module
• A damaged oil pressure sensor or rocker arm actuator should be mended or restored

All the defective wirings or short circuits associated to the oil pressure sensor or rocker arm actuator should be repaired or replaced

There is no need to get strained if your OBD code is still flashing up as we are here at your service. Have a look at our superior variety of engine control module, rocker arm, valve, engine oil pressure, powertrain control module, wiring, VVT and many more. Now all your problems would vanish within no time.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

First and foremost, start by checking the oil pressure of the engine. All the screens of the oil pressure sensor and the rocker arm actuator should be inspected. It is essential to check the quality and the levels of the engine oil. Next, after all this has been done, proceed further to check the wiring connected to the oil pressure sensor and rocker arm actuator for any loose wires or shorted circuits. It is advised to use a multimeter. Further, the technical service bulletins (TSB’s) should be checked as a number of vehicles so have TSBs related to the P2652 code.

Common Mistakes When Diagnosing the P2652 Code

Here we have listed a few common mistakes that should be avoided

• while performing the diagnosis:
• Extremely low engine oil level
• A failure in the powertrain control module
• Malfunctioning rocker arm oil pressure sensor
• Wiring defects