Error Code P2561: What It Means & What To Do?

<<See All OBD Codes

The P2561 error code which does not function properly is known as A/C control module requested MIL illumination. The error code will be set if the A/C control module finds an issue with the air conditioning system and it send a message to the PCM.

The ECM will look after the A/C control module for the malfunction illumination light request signal. The P2561 error code will be set when the A/C control module requests the ECM to ON the MIL.

What causes this problem with the A/C Control Module Requested MIL Illumination?

• The A/C system has some issues.
• Defective A/C control module.
• The harness of the A/C control module might be open or shorted.
• The electrical connection of the A/C control module might be poor.

1. Engine Control Module - Any corrosion or break in the internal wiring harness can cause a short in your ECM. If you’re ECM is shorted, then you must change the engine control module (ECM) as soon as possible to avoid the P2561 error code.
2. Powertrain Control Module - The PCM regulates important functions of the vehicle as well as it has a direct impact on how well your vehicle performs. Fixing your faulty powertrain control module (PCM) will help your engine to run smoothly.
3. A/c Control Module - The P2561 error can be avoided if the defective A/C control module is immediately fixed by getting a new one from PartsAvatar.
4. A/c Clutch Relay - Find the right replacement for a faulty A/C clutch relay from Parts Avatar at affordable prices online.
5. Speed Sensor - If the cruise control is not working properly, then the speed sensor can be faulty. Change it as soon as possible.
6. A/C System - It is easy to get rid of the P2561 error code when the A/C system is replaced as soon as possible.

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P2561 here:

Common Symptoms

• As the air conditioning system is disabled, the cabin cooling might be less or non-existent and the error will get stored in the vehicle.
• Flashing of the malfunction lamp or the service engine soon lamp.
• The code might still be pending if it is stored and illumination of the service engine soon lamp doesn’t take place yet.

Want to correct the Trouble Code P2561? Read these points mentioned below:

• Firstly, check for faults in the ECM/PCM and resolve them.
• Secondly check the A/C control module, and A/C clutch relay for possible defects and change them.
• If you find the speed sensor to be defective, alter it as quickly as possible.

Parts Avatar Canada is here to solve all your issues related to car parts. We have stocked a wide range of best priced ECM, A/C control module, a/c clutch relay, PCM, speed sensor, A/C system, injection, fuel injector, oil pressure sensor and a lot more to help you out in fixing your car.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P2561 code to be stored:

• The data for speed control purpose is used by the cruise control module, and the traction control module will use data to control the vehicle traction control strategy and the anti-lock brake controller can relate the vehicle speed from the PCM with the input data from individual wheel speed sensor to check the anti-lock braking system.
• Fault in the internal control module is usually found by the module, but the CAN bus can also be applicable as other control modules will likely identify the fault, as well as failure of the individual control module is very rare but there is a possibility.
• In order to diagnose the individual control module, check for manufacturer’s recommendation and fix as needed.
• As you replace, all these modules will have to be programmed.
• To diagnose this error, you need multiple tools.
• Begin the diagnosis process with the help of a diagnostic scanner and DVOM.
• Carefully check the wires and connectors for any damages as it can help you to know how this error code occurred and if an irregular connection existed.
• Now, clear every trouble code and see if the error appears again as this can help to determine if a malfunction took place or not.
• Test drive the vehicle by clearing the codes to see if it appears again.
• If you don’t find the error immediately, then it’s mainly because of the irregular condition.
• This is a quite challenging task to perform and so you have to worsen this situation to proceed further with the diagnosis.
• Handing over this major issue to the professionals is a good idea as there are many circuits involved.
• Professionals will use a specialized scanner named Auto hex as it can quickly find the malfunction in the system than ordinary scanners.
• Before you test the system, separate every pin of the CAN bus as it can save time and cut down the cost.
• Install a memory saving device to store memory, in case the PCM and other modules lose their memory and reprogram them if necessary.
• The mechanic will use a CAN scanner as it aptly records the operation of control modules and pin values.
• While the vehicle is functioning, it monitors the circuitry problem without involving any risk.
• You have to fix the shorted or corroded wires, broken connectors if any, as required.
• Recheck the system, once the repair is done, to make sure it is effective. Once you come to know that every component is working properly, connect a scanner to the diagnostic port so can recuperate every code and freeze frame data.
• You will need thousands of individual circuits to diagnose this error with the help of DVOM.
• If you misplace even one probe, then you may end up destroying the costly control modules where you have to reprogram the system. So, you can do a continuity test by disconnecting the control modules which might approximately require 40 hours based on your vehicle.
• Start the process again by checking the wires, connectors, and circuits. Few of the applications will use more than 18 separate control modules for this process.
• Carefully inspect the battery ground for continuity in the control module ground circuits.
• This error code can actually arise if there are defective or faulty system ground.
• Use the auxiliary cable, in case you want to check the differences of system ground as they are highly beneficial.
• Once the repair is done, you will find the straps, wires, and transmission ground cables hanging around which needs fixation.
• Resistance will increase and you will notice the error codes in the system if there are any damaged components. Check for continuity between connectors and controllers with DVOM’s help once you get the wiring diagram of the CAN bus system and the pinout value charts.
• Do you find any open or shorted circuit? Then replace them as specified by the manufacturer.
• Removing the defective or faulty wires is always easy than re-fixing the complicated wire circuits.

Common Mistakes When Diagnosing the P2561 Code

• Some issue might arise with the A/C system which requires more diagnostic procedure.