Guide To P2104 OBD Error Code Solutions
OBD Code P2104 - Throttle Actuator Control System - Forced Idle
Is
your Car’s Check Engine Light illuminating on the dashboard? Do you find sudden
decrease in the fuel economy? And is the car engine running rough with
increased stalling and hesitation? This might be the indication of problems
with the throttle actuator control system of the car which in other words can
be an OBD code P2104 error.
Learn More About OBD Error Code P2104
The throttle actuator control system controls the functioning of the throttle valve and plates to respond to the driver’s request while accelerating. If the control system senses any problem with the throttle response, it puts the throttle into forced idle condition and limits the engine to idle RPM condition. This stores OBD code P2104 in the powertrain control module causing check engine light to illuminate.
What causes this problem with the Throttle Actuator Control System - Forced Idle?
- There might be an open or shorted circuits between the TPS, PPS, and the powertrain control module
- There might be inoperative TPS or PPS
- Some electrical connectors might be corroded
- Unusable drive-by-wire actuator motor
Replace/Repair These Parts To Fix Code P2104
- Throttle
Position Sensor - If you find out that there
are no misfire codes and a common cause of acceleration stumble is a faulty
throttle position sensor. So it is very important to replace the throttle position sensor with us at equitable
prices.
- Engine Control
Module -
Dead cells in batteries can cause a failure in the engine control module. Many
times a battery is left in the rig long after a cell has died. This would
affect the grounding in the car battery.
- Powertrain Control
Module -
If there are some faults in the PCM, then it may throw off the timing and fuel
settings of the engine, which can negatively affect the performance. A flawed
PCM may cause the vehicle to experience a reduction in fuel efficiency, power
as well as acceleration.
- Pedal
Position Sensor - The APP sensor essentially
tells your car engine that how fast or slow to drive as you will press the gas
pedal. When you press down or lift off the throttle, it would send an
electrical signal to the vehicle’s ECU or ECM and then would transmit that signal
to the fuel system. Visit us to purchase top notch pedal position sensor online
at affordable prices.
- Electronic Control
Unit - Do you know that the poor
performance or unexplained drops in fuel economy or efficiency are often
associated to onboard car computer problems, or defective ECU issues?
- Diagnostic Tools – Use factory grade diagnostic tools to resolve OBD code
P2104 error. Buy new diagnostic tools and equipment for us.
Symptoms Of The OBD Error Code P2104
We at Parts Avatar Canada care for our customers, and that’s why we will help you to diagnose P2104 code by listing out some major symptoms. They are mentioned below as follows:
Common Symptoms
- Visibility in the check engine light and this code might be set in the memory of the engine control module
- Car engine might lack power
- There might be restricted throttle control
How To Correct P2104 Throttle Actuator Control System - Forced Idle
Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:
- Repair or replace the quirky TPS
- Rehabilitate the defaults in the electronic control unit
- The malfunctioning PPS should be repaired or replaced as per the need
- Carefully adjust the faults in the drive-by-wire actuator motor
- The PCM/ECM should be restored to working order
Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of ETCS, APPS, PCM, Throttle plate, and Limp home mode, TSB, Bulkhead, Terminals, DVOM and a lot more. We are sure that now all your issues would be resolved.
Other Diagnostic Codes Related To OBD Code P2104
Easy Diagnosis Of Engine Error OBD Code P2104
- Accelerator
pedal position (APP) assembly might start failing
- Some
issues related to the blockage in the intake system
- There
might be loss of calibration in the powertrain control module
- Defects
in the throttle control motor
- Sometimes
the mechanic won’t be aware about the blocked air filter, which might cause a
lot of issues later on
- Issues
with the car wiring