P2082 - OBD Trouble Code

<<See All OBD Codes

OBD-II code displays a declined engine performance and is called as an exhaust gas temperature sensor circuit range/performance bank 2 sensor 1. The temperature of the exhaust gas which keeps going in and out of the SCR that is, a selective catalytic reduction is conveyed by the EGT sensor to the PCM. Any irregular signal which is found by the PCM in the EGT sensor will immediately result in storing of the error code in the vehicle.

The P2082 error refers to the readings of the exhaust gas temperature sensor which seems to be out of range. When the ECU finds out these out of range sensor readings in the bank 2 sensor 1, it sets the check engine light in the vehicle. You will find this check engine light on the dashboard. While this check engine light is on, the ECU will initiate the failsafe mode in order to safeguard the vehicle. Until the normal operation is found or this error is repaired, the fail-safe mode will be set in the vehicle.

What causes this problem with the Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 2 Sensor 1?

• The wiring harness of the EGT might either be open or short.
• Leaky exhaust.
• Failure of the EGT sensor.
• Weak electrical connection.

1. Exhaust Gas Temperature Sensor - The EGT sensor can turn out to be faulty if the diesel particulate filter is clogged too much. Repair or replace the damaged EGT sensor quickly.
2. Engine Control Unit - If the ECU is damaged, it can cause sudden jerking or stopping of the vehicle. It’s best to replace the damaged ECU with a new one to avoid further malfunctioning of the vehicle.
3. Transmission Range Sensor - The transmission range sensor defines the transmission speed, where this information is used to calculate as to which gear is needed and the shifting time. If you find the transmission range sensor to be faulty replace it immediately.
4. Engine Control Module - You can easily find out that the engine control module in your vehicle is damaged if your vehicle faces issues like stalling or misfiring. Additionally, the behavior of the engine can be erratic. In one such scenario, it is always best to replace the faulty engine control module.
5. Powertrain Control Module - The PCM will monitor and compensate for any change in altitude and looks after the overall health of your car. The right replacement for your faulty powertrain control module can be found at Parts Avatar at the best prices.

Willing to know some common symptoms of OBD Code P02BD? Your wish is our demand. Have a look at them below:

Common Symptoms

With respect to the P2082 error code, the driver may not notice any symptoms at all. At times the only indicator for this error code is that the check engine light will be set in the vehicle.

We have listed out some ways which would help you to correct the occurrence of OBD Code P2082. They are mentioned here as follows:

• The wiring harness must be changed or fixed.
• Resolving the weak electrical connection.
• The EGT sensor needs replacement.

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of air-fuel ratio sensor, crankshaft sensor, injection pump, oxygen sensor, transmission range sensor circuit and many more. Now all your problems would vanish within no time.

If you want to easily diagnose this P2082 fault code, then all you have to do is to follow the steps which are mentioned below:

• The mechanic will start the diagnostic process by checking the ECU for any codes that are stored which also includes the pending codes and history of codes.
• Each code has its own freeze frame data that is linked with it, which in turn informs the mechanic as to in which condition, the vehicle was when the error code was initiated such as RPM, speed, coolant temperature, and calculated load.
• Each of these codes and freeze frame data will be carefully noted and then cleared off. Next, the mechanic will try to test drive the vehicle by attempting to duplicate these error codes.
• The P2082 error code will be confirmed after the test drive has been performed.
• Now the mechanic will visually inspect the vehicle, by checking for any signs of defects to the EGT sensor or its related wiring.
• Next, the mechanic will use a scan tool to verify the data stream in order to read the readings of the EGT sensor and relate both bank 1 and bank 2.
• Secondly, the mechanic will use a multimeter to check for the correct voltage at the position of bank 2 sensor 1 EGT sensor.
• Finally, check for any leaky areas in the exhaust.

Common Mistakes When Diagnosing the P2082 Code

Most often, either the leaky exhaust or the damaged wires are overlooked as a result of the P2082 error code. These are very minor issues which can be fixed easily. If they are not noticed initially while performing the diagnostic process, you will end up doing large repair works by wasting time and money.