P0C5F OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0C5F can be defined as Drive Motor "B" Position Sensor Circuit "B". This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. The particular code which is triggered depends upon the specific fault which the PCM has detected. If there is some issue with the automobile’s drive motor "B" position sensor circuit "B", then the P0C5F fault code would start flashing up.

We learn more by looking for the answer to a question. That’s the reason why we are here to provide you the answers for all your questions. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

What causes this problem with the Drive Motor "B" Position Sensor Circuit "B"?

• Imperfect hybrid vehicle motor assembly
• There can be unlocked hybrid vehicle motor assembly harness
• Hybrid vehicle motor assembly circuit electrical connection might be inadequate
• Some issues related to the HV control ECU

1. Generator Assembly - Thinking of starting your car with faulty generator assembly? The car won’t be able to start because the bad generator assembly won’t charge the car battery when the automobile was running.
2. HVAC Blower Motor Control Module - Are you wondering why your car’s HVAC Blower Motor Control Module is not working properly? Then it can be due to a blown power supply fuse, a faulty motor ground connection, quirky motor speed control module or sometimes sure to a failed motor.
3. Motor Assembly - If you are hearing a loud clunking noise, while shifting your automobile, then it is a sign of motor assembly failure. Get your motor assembly inspected from a mechanic.
4. Engine Control Module - The solenoid might cause a short in the engine control module because of corrosion in the solenoid or the wire running from the solenoid to the ECM harness.
5. Powertrain Control Module - A trouble with the PCM would mean that it is unable to determine the right fuel mixture and would send the car engine either more or less fuel than it requires. Now when the engine gets more, the carbon emission would increase and fuel economy would drop. In case of the opposite, the engine will choke, stutter, and might start stalling sometimes.

Willing to know some common symptoms of OBD Trouble Code P0C5F? Your wish is our demand. Have a look at them below:

Common Symptoms

• An illuminated engine light (or service engine soon warning light) may be observed

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0C5F:

• Recondition the non-functioning hybrid vehicle motor assembly harness
• It is essential to restore the flawed hybrid battery
• Repair or replace the quirky powertrain control module
• Rehabilitate the defaults in the hybrid vehicle motor assembly
• Adjust the flawed motor control module

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade drive motor generator, motor position sensor, motor control module, generator assembly, drive motor output shaft and a lot more for our precious customers.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

A technician begins by hooking the vehicle to an OBD-II scanner to verify that the code is present, and check for other codes. The freeze frame data along with current data is recorded, and the codes are then cleared to see if they reoccur.

Visual inspection of the wiring and connectors to check for loose connections, corrosion, or shorts is done.

A specialized tool may be used to test the drive motor "B" position sensor circuit. Other tests of the drive motor "B" position sensor circuit and its components may help pinpoint the problem, as well as inspection of the wiring and connectors. 

Now if all the components check out, inspect for the fault in the PCM as it can sometime store wrong OBD code and thus might need replacement or reprogramming.

Common Mistakes When Diagnosing The P0C5F Code

• Defaults in the drive motor generator assembly