P0C06 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0C06 can be elucidated as Drive Motor "A" Phase U-V-W Circuit Low. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

Are you tensed because the P0C06 fault code is flashing? We have got everything which you need and at equitable prices. You must visit us and we promise that you will never regret your decision. The resistance of the thermistor which is built into the motor temperature sensor would change as per the changes in the temperature of the MG2. Now if the temperature of the MG2 would be low, then the higher would be the resistance of the thermistor. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present.

What causes this problem with the Drive Motor "A" Phase U-V-W Circuit Low?

• Quirks in the hybrid vehicle motor assembly
• There can be opened or shorted hybrid vehicle motor assembly harness
• Unsatisfactory electrical connection in the hybrid vehicle motor assembly circuit

1. Motor Assembly - A faulty Motor Assembly can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Motor Assembly Harness - If everything is alright with PCM, then there is surely some defect in Motor Assembly Harness. Get it replaced before the situation gets worse.
3. Engine Assembly - P0C06 code can display due to some faults in the Engine Assembly. So it is very important to replace the Engine Assembly with us at equitable prices.
4. HV Control Module - Do you remember when was the last time you got your car HV Control Module checked up? A dirty HV Control Module can cause a lot of issues like displaying P0C06 code.
5. Engine Control Module - Poor Engine Control Module can cause a lot of difficulties, so why not get it replaced at time?
6. Hybrid Battery - Are there some faults in your Hybrid Battery? Don’t waste time and get them replaced or else P0C06 code can turn up.
7. Automatic Transmission Module - OBD Code P0C06 can appear because of faulty Automatic Transmission Module.
8. Powertrain Control Module - There can be some issues with the Powertrain Control Module due to which you may see P0C06 code appearing over and over again. Visit us to buy best quality PCM online.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Check engine light might come into signal
• Non working high voltage system

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• It is essential to restore the flawed powertrain control module
• Repair or replace the quirky hybrid vehicle motor assembly
• Rehabilitate the defaults in the motor control module
• Recondition the non-functioning hybrid vehicle motor assembly harness

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of hybrid powertrain control module, body control module, power inverter and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

After verifying the P0C06 code with an OBD-II scanner, the mechanic should begin with a visual inspection of all electrical components, especially looking for leaking fluid that could have caused shorts or corrosion. Any issues should be repaired, and the code should be cleared from the system. If the code reappears after a retest, the mechanic should then move on to performing voltage tests and resistance tests on the sensor, and comparing the information to the manufacturer’s specifications. If the readings are within the correct limits, then the sensor needs to be replaced. However, if the readings are not within the correct limits, then the issue lies elsewhere. The mechanic should continue checking each possible cause, clearing the code and retesting the system after each attempt, to be sure that the correct solution is found.

Common Mistakes When Diagnosing The P0C06 Code

• Drive motor generator power inverter control module related issues
• Quirks in the drive motor generator assembly