Error Code P0B01: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0B01 can be explained as Auxiliary Transmission Fluid Pump Motor Phase U Current Low. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. The engine control module, powertrain control module or the transmission control module monitors this circuit depending upon the particular automobile.

Do you want to know more about the P0B01 fault code? Don’t worry! Parts Avatar Canada is here at your service. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another. If the engine control module would detect a variation in the voltage coming from the auxiliary transmission fluid pump motor that is outside the parameters set by the automobile manufacturer, then it would store the P0B01 error code. This would also give rise to the illumination of the check engine light.

What causes this problem with the Auxiliary Transmission Fluid Pump Motor Phase U Current Low?

• Some flaws in the auxiliary transmission fluid pump  
• Auxiliary transmission fluid pump harness might be opened or sometimes shorted
• Auxiliary transmission fluid pump circuit might have inadequate electrical connection

1. Powertrain Control Module - A faulty Powertrain Control Module can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Automatic Transmission Fluid - If everything is alright with PCM, then there is surely some defect in Automatic Transmission Fluid. Get it replaced before the situation gets worse.
3. Engine Control Module - P0B01 code can display due to some faults in the Engine Control Module. So it is very important to replace the Engine Control Module with us at equitable prices.
4. Transmission Fluid Pump - Do you remember when was the last time you got your car Transmission Fluid Pump checked up? A dirty Transmission Fluid Pump can cause a lot of issues like displaying P0B01 code.
5. Muffler - Poor Muffler can cause a lot of difficulties, so why not get it replaced at time?
6. Exhaust System Parts - Are there some faults in your Exhaust System Parts? Don’t waste time and get them replaced or else P0B01 code can turn up.

There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P0B01? Your wish is our demand. Have a look at them below:

Common Symptoms

• Check engine light might come into signal

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• It is essential to restore the flawed auxiliary transmission fluid pump 
• The malfunctioning powertrain control module should be repaired or replaced as per the need
• Carefully adjust the faults in the auxiliary transmission fluid pump harness
• Adjust the flawed auxiliary transmission fluid pump circuit

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of custom exhaust, slp exhaust and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0B01 code to be stored:

The original multi-displacement system turned off opposite pairs of cylinders, allowing the engine to have three different configurations and displacements. P0B01 code had an elaborate diagnostics procedure, including showing engine trouble codes on the air conditioning display. However, the system was troublesome, misunderstood by customers, and a rash of unpredictable failures led to the technology being quickly retired.

Common Mistakes When Diagnosing The P0B01 Code

• Common mistakes while diagnosing this trouble code are unnecessary and expensive replacements which usually happen when one don’t follow all the steps carefully. In this code usually people replace auxiliary transmission fluid pump motor without even properly diagnosing it.
• The most common mistake while diagnosing this code is missing out on diagnosing steps which further leads to the expensive and unnecessary replacements. It is always recommended to seek help of experienced diagnostician to avoid any mistakes.