P0A81 - OBD Trouble Code

<<See All OBD Codes

The trouble code P0A81 can be explained as Hybrid Battery Pack Cooling Fan 1 Control Circuit/Open. The cooling air would start flowing into the inlet on the right of the rear seat and would then travel through an intake duct to the battery blower assembly on the right surface of the luggage compartment. The cooling air would travel through an intake duct which would then connect the battery blower assembly to the upper right surface of the HV battery assembly and then it would simply flow to the HV battery assembly.

Do you want to know more about the P0A81 fault code? Don’t worry! Parts Avatar Canada is here at your service. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

What causes this problem with Hybrid Battery Pack Cooling Fan 1 Control Circuit/Open?

• Quirks in the battery cooling blower assembly
• There can be opened or shorted battery cooling blower assembly harness
• Unsatisfactory electrical connection in the battery cooling blower assembly circuit
• The integration relay might not be functioning properly
• There can be inoperative battery smart unit
• Defective power management control ecu

1. Integration Relay - A faulty Integration Relay can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Hybrid Battery - If everything is alright with PCM, then there is surely some defect in Hybrid Battery. Get it replaced before the situation gets worse.
3. Car Battery - P0A81 code can display due to some issues in the Car Battery. So it is very important to replace the Car Battery with us at equitable prices.
4. Electronic Control Unit - Do you remember when was the last time you got your car Electronic Control Unit checked up? A dirty Electronic Control Unit can cause a lot of issues like displaying P0A81 code.
5. Body Control Module Component - Poor Body Control Module Component can cause a lot of difficulties, so why not get it replaced at time?
6. Engine Control Module - Are there some faults in your Engine Control Module? Don’t waste time and get them replaced or else P0A81 code can turn up.
7. Powertrain Control Module - OBD Code P0A81 can appear because of faulty Powertrain Control Module.

There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P0A81? Your wish is our demand. Have a look at them below:

Common Symptoms

• The service engine soon light can start lighting up
• No operation of the high voltage system

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Fix the defaults in the ECM/PCM
• It is essential to restore the flawed battery smart unit
• Repair or replace the quirky integration relay
• Rehabilitate the defaults in the battery cooling blower assembly
• The malfunctioning power management control Ecu should be repaired or replaced as per the need
• Carefully adjust the faults in the battery cooling blower assembly circuit
• Recondition the non-functioning battery cooling blower assembly harness
• Adjust the flawed electrical connection

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of battery blower, battery cooling fan, battery connectors and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0A81 code to be stored:

• The mechanic or the technician will use a diagnostic scanner or code reader like DVOM to visually scan for the error codes in the vehicle.
• After performing a careful inspection, every of the stored codes and freeze frame data are retrieved as it can help down the way for further diagnosis process.
• Most often he has to inspect the solenoid itself to see if they are faulty or damaged. Additional error codes that are stored in the vehicle are also addressed.
• The mechanic performs a continuity test between the PCM and solenoid to check the resistance.
• If the solenoid or the control modules are not faulty, he will then retune the code and test drive the vehicle.
• On test driving, if the P0A81 code does not return soon, he will know that an erratic condition exits.
• But if the error returns instantaneously, he will check every components of the control module as well as the circuit like connectors, wires, harness, fuses etc for any possible fault.
• If any component is damaged, he will fix them right away.
• After performing this repair, he will inspect the transmission fluid as well as its level.
• If the level is below the manufacturer’s specification, it has to be refilled and if the fluid is murky or contaminated it needs to be replaced.

Every time a repair work is carried out, make sure that the mechanic test drives the vehicle after every repair so that the diagnosis is successful. This can eventually help him to know as to where the error occurred.